I am working on superalloys 617, I found that at many occasions my aged materials shows strain hardening value > 0.6.
Please share a comment on this.
I hope you are using Ludwick–Hollomon power-law relation between true stress and true plastic strain; because value of n > 0.6 is a bit unusual
Yes.Your are correct.
I am about to start making Li-ion battery, but I want an idea to start with. Should I make electrode material, binders and slurry or what is the best way?
10 November 2017 4,848 2 View
I need to understand the problems in batteries for instance: dendrimer growth and diffusion problem, SEI issues ans many other problems to solve for a better battery. Which software is good to use...
10 November 2017 1,958 0 View
Catalyst affects the growth of polymer, but how does the amount of catalyst affects the polymer growth?
10 November 2017 310 4 View
Why and How the stress triaxiality in a material becomes greater than 1? What is the physical significance of it? Kindly throw a light on it. Regards Aditya
06 July 2017 7,722 13 View
In Alloy 617, in its as-received condition the twins are more prominent, but as aging proceeds twins disappear, Why? Can one measure stacking fault energy (SFE) with TEM?
05 June 2017 1,375 3 View
The origin of loss of ductility is primarily due to intergranular fracture. When such fracture occurs, polycrystalline material shows a severe brittleness & poor ductility, irrespective of...
07 August 2016 5,341 6 View
The Engineering Stree/Strain, true stress/ strain are normal values one get from tensile data. What other material properties can be obtained from tensile data?
07 August 2016 6,354 6 View
Luders band arises in low carbon steels and these bands then requires less stress for their propagation than for their formation because of the freeing of dislocations from their solute atmospheres.
07 August 2016 1,540 4 View
How to define a grain in relation to metallurgy? Is it a right to say :a grain consists of crystals oriented in a particular direction ?
07 August 2016 6,239 4 View
The results from TEM analysis for alloy 617 has revealed gamma prime phase Ni3(Ti,Al) but in addition to this Some precipitates of Ni3Si is also obtained. What is the significance of this new...
03 April 2016 9,384 1 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
How select composition for ods-high entropy alloys?
31 July 2024 2,795 1 View
Any suggestions with respect to etchant composition and holding time?
27 July 2024 6,925 2 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...
13 July 2024 9,003 2 View
Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...
13 July 2024 2,417 1 View
In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....
11 July 2024 4,476 3 View
Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...
24 June 2024 1,605 0 View
Is there any suggestion on the explanation and reduction of stacking fault defects in high Al content InAlGaAs alloy lattice matched to InP?
24 June 2024 6,645 1 View
For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...
13 June 2024 2,504 0 View