Can someone suggest to me a model (preferably an open source one) to model the dynamics of a coastal limestone (karstic) aquifer?

More Selvarajah Pathmarajah's questions See All

Should dissolved organic-N (DON) in river, stream and lakes be monitored as routine trophic N-index in addition to nitrate, ammoniacal-N and total-N?

Nitrogen contamination of the surface water (lake, river and stream) is monitored routinely as nitrate-N, ammoniacal-N (both of the above combined as dissolved inorganic-N) and total-N. The above...

14 June 2020 1,748 0 View

A best and quick reference to learn about designing Convolutional Neural Networks form scratch?

HI, I am relatively new to CNN and would like to start working on a deep learning problem using CNN. Anyone got a detailed and quick reference to learn about this? Thank you. Thuseethan

27 April 2018 2,265 3 View

Can anyone know step of symmetric and asymmetric modeling and forecasting in R code?

Hi All, can anyone know step of symmetric and asymmetric modeling and forecasting in R code If you have a journal/paper related to this, please let me know because it's for my final task.....

28 December 2017 4,718 3 View

Wasetwater from TF treating only domestic wastewater requires further treatment to reduce NH4. Would aerating without RAS trigger good nitrification?

A current modern trickling filter (TF) system with plastic filters has an input of BOD = 200 mg/L, COD = 350 mg/L and TN = 45 mg/L (effluent volume being 15,000 m3/d) has an output (in mg/L) of...

13 May 2017 8,021 23 View

Is there a spilling parameter in VASP?

In CASTEP and Quantum Espresso, the spilling parameter can be used as an estimate of how well the total DOS is projected onto the atomic orbitals. A small spilling parameter implies a good...

03 February 2016 390 2 View

Is the use of nitrification inhibitors to reduce nitrate leaching from soils being monitored or regulated in your country? If so why and how?

Nitrification inhibitors have been researched extensively for more than 5-6 decades. If used properly, NO3 leaching and greenhouse gas emission such as N2O from soils can be minimised in...

08 April 2015 4,643 14 View

How can I configure glew and freeglut in Visual Studio 2010?

I would like stable versions and structured tutorials with source code to work on one application to render 3D models using OpenGL.

21 March 2015 129 4 View

Can anyone suggest me a suitable language and toolkit to make simulations for a real time video input?

My idea is to develop a 2-dimensional simulation for a real time traffic camera input. I need to create agent objects for each vehicles and pedestrians in real time video captured via camera. I...

05 February 2015 7,327 2 View

Is there sufficient evidence for NO3 to be immobilised in soil?

Ammonium (NH4) is immobilised by soil bacteria which is a common pathway in N cycle. Nitrate (NO3) is reduced to N2O or N2 via denitrification process. Sometimes NO3 can be reduced through...

21 January 2015 2,100 9 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Saravanamuttu Subramaniam Sivakumar

This is an acute problem in Jaffna peninsula of Sri Lanka, We can try to put a impervious curtain along the sensitive sea discharge locations.

Christopher J Brown

I believe there are some new versions of the USGS code SEAWAT which should be able to help model the situation proposed. SEAWAT is in the public domain in the US.

Selvarajah Pathmarajah

Thanks a lot Christopher. I will look for it.

Cynthia Dinwiddie

MODFLOW-DCM (discrete conduit model)

http://books.google.com.pe/books/about/Enhanced_Characterization_and_Representa.html?id=RvVtMUj2cIQC

Thanks Cynthia.

Husam Baalousha

MODFLOW-CFP

Thanks Husam. Will try

Subhajit Dey

USGS SEAWAT, MODFLOW with seawater intrusion package, Also you can used Strack(1976) base models. In my opinion SEAWAT is the best