Specify the Burgers vectors for dislocations, which cannot be uniquely identified.?

1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...

20 February 2021 2,370 1 View

How to improve dissolution of neosome?

I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...

17 February 2021 3,584 1 View

What is the best method for preparation of Polymeric nanoparticles for co-delivery?

We are planning to make Polymeric nanoparticles for co-delivery of 2 flavanoides. Which is the best method, that one should follow.

09 February 2021 7,086 8 View

OmniScriptum Publishing Group?

Hello, Has anybody published with OmniScriptum Publishing Group. I got an email from them. The emails claims the editor is from the group but the email is signed out by lambert academic...

08 February 2021 5,611 3 View

I'm interested to quantify Urea by HPLC method, reversed phase conditions are preferable. Is there a good method suited for urea?

I have to develop a method that can be good enough to run dozens of samples that include urea as the main compound. I prefer an HPLC method because of the convenience of running large numbers of...

01 February 2021 1,888 4 View

How to convert ng/ul of DNA concentration to pmol/ul ?

Dear researcher, After amplifying my target gene (1900bp) into the required cDNA by PCR,>cut specific gel bands and purify the gel and the concentration was 30ng/ul. Next, performed A-Tailing...

21 January 2021 2,671 3 View

Can use Unigenes from RNA sequences for overexpression studies (transformation) without requiring a specific plant genome?

Dear researchers: If the plant genome has not been released yet, can Unigenes from RNA sequences be used after BLAST and confirmed with known Arabidopsis genes for function/overexpression...

20 January 2021 5,557 2 View

Following is XRD of iron oxide nano material synthesised using bipyridine derivatives. What are the reasons for Broad Humps?

Even after few repetitions..I am getting similar results. Is is due to organic components?

20 January 2021 9,279 6 View

What is the reason of weight gain in TGA curve of a HDPE polymer sample ?

HDPE samples were aged at higher temperatures in the presence of water and CO2 than the TGA test was performed in Nitrogen? Weight gain is seen in the curve? What could be the possible reason for...

16 January 2021 5,644 2 View

Can BLAST/ search by using known Domain in Transcriptome/Genome data for a gene family?

Dear Researchers, I have Transcriptome/Genome data and want to list all the member of a KCS/CER gene family whose Domain AP2/ERF, FAE1_CUT1, according to the Arabidopsis database, so is there...

15 January 2021 2,293 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View