01 March 2024 1 5K Report

Can somebody recommend a book about Urban Canopy flows numerical modelling?

More Juan Carlos Álvarez Hostos's questions See All
?como elimino articulos que no son propios?

eliminoar articulos que son de tu autoria

05 July 2024 2,107 1 View

How to calculate the proportions in grams or milliliters of the compounds for 60 mL of SAPO-11 zeolite precursor gel?

It is required to make a precursor gel for a SAPO-11 Zeolite, the compounds are the following: * As a source of Al: Aluminum Isopropoxide (98%) Formula: C9 H21 O3 Al PM: 204.24 g/mol Density:...

01 July 2024 617 3 View

How to reduce the material coming out of the torque rheometer?

A physical mix was in vitro evaluated on a torque rheometer. The composition was predominantly recycled polypropylene (PP), yet the melt flow index (MFI) was found to be excessively high....

25 June 2024 10,154 0 View

Dyslexia and Virtual Reality yes or no?

Do you think the use of virtual reality with dyslexia students is good?

23 June 2024 8,437 2 View

Who is the use of Generative Artificial Intelligence in Qualitative Research?

One of the most intriguing frontiers in contemporary research is the application of Generative Artificial Intelligence (GenAI) in qualitative research. This technological advance offers tools that...

13 June 2024 781 2 View

¿Que enfoque metodológico me recomiendan para abordar los gremios tróficos en un área natural de BST?

Me interesa investigar la distribución espacial de los gremios tróficos de aves en un área natural específica de bosque seco tropical, analizando la abundancia relativa de cada gremio en las...

12 June 2024 9,313 1 View

Condensation of a Q8 serendipity FE to a Q4 FE with drilling DOFs?

Hello, Can somebody please give me some reference to a paper or book where it is explained how to condensate: * from a Q8 serendipity FE to a Q4 FE with drilling DOFs (16 DOFs to 12 DOFs). *...

05 June 2024 936 1 View

Laser for perovskite module?

Hi, I'd like to know if someone knows about a company where I can buy an affordable laser-scriber for perovskite films and another thin film for the fabrication of modules. Many thanks,

31 May 2024 2,841 0 View

Fluorescence spectroscopy: signal from water?

In order to proceed with the quantification of an Azide Alkyne Cycloaddition reaction efficiency by using a fluorogenic probe with Cy5-DBCO, I first need to construct a calibration curve. The...

16 May 2024 6,266 5 View

Can I calculate the high and low spin of the material in Quantum espresso?

I would like to simulate the high and slow spin configuration of a metal oxide. I am using QE for it, but in my research, I found that this kind of calculus is not possible. Or if it is possible,...

15 May 2024 6,497 3 View

Similar questions and discussions
How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Do you know any references for analyzing stochastic fiber orientaion composites ?

Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...

04 August 2024 3,461 3 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close