Can some one tel me what are the parameters are considered for flow analysis high storey building?

More Rajasekarababu Kb's questions See All

Why Pressure distrution study is important for Tall buildings <200 m ?

Buildings are made of concrete (Strong and stiff) then why wind load are much important for tall buildings. Why builders are looking wind loads on tall building. Can any one explain in detail...

08 September 2018 9,858 0 View

Standard deviation error in Fluent?

Hello, I am simulating circular cylinder, i want to extract standard deviation of a Cp on a surface, I projected point over the cylinder and i report and save the file in the folder. But my...

07 August 2018 2,684 0 View

Why most of the wind engineering problems are solved by steady RANS models?

I have a question on wind flow around the building using CFD. Why the most of the people are using steady RANS (RANS) models instead of Transient (URANS and LES). The flow will be stochastic...

07 August 2018 4,673 5 View

How to make surafce points in ANSYS FLUENT USING Excel?

Hai Every one, I have a question about surface points in ANSYS FLUENT 18. I know I could input the coordinates in the surface->points option. But I have more than 200 points to monitor.it...

03 April 2018 7,942 0 View

How to write each time step of pressure coefficent in ansys fluent using %t.txt?

Hi, Every one, I am trying to write each time step of pressure coefficent uisng macros in ANSYS FLUENT in my model. After long serach and i found one document (ATTACHED) ,which mentioned like...

03 April 2018 6,246 0 View

Building simulation, I recently simulated open terrain profile using IDDES and DDES turbulence model.?

i gave my first cell height is 0.0020 accordingly with roughness measurements (0.0019) Ks< first cell height. Can i run this model in LES. ( Model height is 0.7 , width is 0.15m and Domain...

07 August 2017 3,382 3 View

How to find Cd mean and Cl rms in ANSYS fluent?

Hi, I saw some of the paper mentions Cd mean and Cl rms coefficients, I dont know how to switch in ANSYS fluent. help me to switch or please explain about it. I attached a image for your refernce...

09 October 2016 9,465 2 View

How to switch IDDES ( improved delayed detached eddy simulation )in ansys fluent?

Hi, I want to switch IDDES in fluent. Any one help me to switch this in ANSYS Fluent 16. Looking Forward.

07 August 2016 7,526 0 View

How to relate the strouhal number FFT fluent to manual calculation St= FD/V?

Hi, my analysis is on cables, I found that St = 0.4 in fluent FFT using (Power spectral density) and Frequency is 7.75 Hz. But calculating manually i am getting 0.06 = St. (D=0.155, V= 18 m/s,...

02 March 2016 944 5 View

How to justify this coefficient of pressure (Cp) in this Building ?

Hi, I have done DES simulation on tall building structures. In this simulation, Cp[ PRESSURE COEFFICIENT] contours and Graph are showing in negative sign. Is the simulation is correct? Please...

02 March 2016 3,376 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Rajeev Kumar Singh

Can you be more specific on what you want to analyse in flow analysis in buildings. You may study the thermal load, ventilation, air flow and many other aspects. Your boundary conditions may depend based on that

Rajasekarababu Kb

sir,

Thank you. I want to analyse aerodynamic behavior over a structure...

Mohamed Ali Bek AbdelRhman

You can extract the wind velocity around the buildings and the pressure as well.