How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

When is it unnecessary to change organisational culture?

As a former management practitioner, I recall a generally accepted view that changing organisational culture is difficult, so you should only attempt it if the organisational change that you are...

27 February 2021 2,595 8 View

Can I use a protein-devoid condition as my negative control in ELISA?

Hello, I am running a sandwich-type ELISA where I am trying to inhibit a protein-protein interaction using small molecules. For each experiment, I determine my Z' (Z-prime) to determine the...

23 February 2021 7,429 1 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

How to discriminate between Sentinel-2 Level-2A Product Discriminators?

According to the Sentinel-2 user guide here (https://sentinel.esa.int/web/sentinel/user-guides/sentinel-2-msi/naming-convention), the compact naming convention is arranged as...

21 February 2021 5,919 9 View

Are ZnS nanoparticles moisture sensitive?

Hello Everyone, I tried to form ZnS nanoparticles using the hot injection method and was able to form the same (confirmed by XRD). When I centrifuged, after the reaction I got a kind of white...

17 February 2021 1,709 3 View

Will SARS-CoV-2 Spike be broken into S1 and S2 by denaturing conditions?

Hello, I am performing a western blot of my SARS-CoV-2 Spike-pseudotyped lentiviral particles. I denature my virus by adding concentrated virus to 2X Laemmli buffer at 1:1, then boiling for...

17 February 2021 4,844 4 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How relevant is Mini slump cone?

for all the rheology researchers, my question is, how relevant is a mini slump cone (smaller than a standard 50 cent rheometer). currently based on testing, the thickness of slumped material is...

26 February 2021 3,668 1 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to reduce residual stresses in MD simulation?

I am working on a preparation of representative polymeric structures of some popular polymers, such as polyimide or PTFE for MD simulation, during which a single nitrogen or oxygen atom will be...

24 February 2021 8,105 3 View

Suggestions for occupational stress surveys?

I am currently writing a masters thesis on reasons for occupational stress in the early childhood classroom, and want to include a short survey assessing participants work-related stress levels. I...

24 February 2021 8,678 2 View

Could anyone recommend papers that focus on mixed-ethnicity Black-Caribbean/Caucasian adopted children?

Dear All, I have been looking for papers, or books, that focus on the issues surrounding adoption of mixed Black-Caribbean/Caucasian children. I am interested in literature that looks at any...

22 February 2021 8,466 2 View

The most suitable method to calculate the stress intensity factor in the presence of contact between the crack lips?

I'm trying to study cracked structures under a compressive load taking into account contact between the crack lips. I would like to know if the method of extrapolation by displacement remains...

21 February 2021 8,694 4 View

How COVID-19 has affected mental health?

The pandemic has led to depression and anxiety and its negative effects shouldn't be ignored. However, it has also led some people to become more resilient! What do you think? Thank you.

21 February 2021 4,733 19 View

Can medicinal plants really play an inherent rule in the COVID-19 tackle?

Numerous scientific reports cited plant extracts with potential antiviral activity and even anti-COVID-19? Why these findings are neglected? I remember very well the warning released by the WHO to...

17 February 2021 2,141 9 View