How can I find the effect of different parameters like (Reynolds number, Hartman number, volume friction etc.) in COMSOL?

Here I am facing this problem. I don't find any effect of this type of parameters. I am a beginner user of COMSOL.

23 February 2021 9,086 3 View

Can i quantify protein concentration in sds page?

I have to quantify a mixture of proteins. But I can not quantify its concentration by any protein detection methods as the values fluctuate. Can i quantify the protein concentration by sds page?

22 February 2021 215 2 View

Can fractal dimension of thin film surfaces affects the electrons energy states?

As fractal dimension of a thin film surface implies the irregularity in the surface. Is it possible that the energy states of the electrons are also affected by the fractal dimension?

19 February 2021 5,509 3 View

Can we use image data in MATLAB Neuro Fuzzy Designer ?

I have remotely sensed data (image) that I want to use in the Neuro-Fuzzy Designer apps of MATLAB. Is it possible to use an image file in the Neuro-Fuzzy Designer app or only numeric data is...

17 February 2021 1,205 5 View

Is it possible to determine % K2O of organic manures by STPB method ?

To determine % K2O of organic manures, flame photometric technique is used whereas in inrganic fertiliser for K2O determination STPB method is used. I am trying to find out any method of...

24 January 2021 4,714 3 View

How to tackle "CONSTRAINT CONTROLS" error while using tie between CFRP and frame segment in abaqus?

Hello, I had been trying to model a portal frame wrapped with CFRP in ABAQUS. To tie the CFRP laminates with frame I need to use slave/master surface interaction. But whenever I try to model the...

19 January 2021 2,906 3 View

How to remove colour from DNA pellet during DNA extraction?

I am working with Amaranth accessions which are green to red in color and contain high phenolic compounds. Using the CTAB method with the slight modification I am trying to get high-quality DNA so...

18 January 2021 3,578 1 View

Why the mixture of NaOH solution (10-12M) and Na2SIO3 solution is getting solidify after mixing?

These days I am noticing that the mixture of NaOH (NH) (10-12M) and N2SiO3 (NS) solution gets solidify after 24 hours. The ratio of mixture of NS to NH is 2. To mention, the same solutions that we...

18 January 2021 7,911 2 View

Which model is most suitable for urban simulation?

Respected sir/mam, I want to simulate the urban expansion using different time series LULC based on satellite image. please suggest me most suitable model for urban simulation. Thanks and regards.

17 January 2021 9,134 11 View

Is there any packages or code of MATLAB for solving a system of stochastic delay differential equation?

Hello, Can you help me regarding MATLAB solver for a system of stochastic delay differential equations? To be specific the system is delay differential equation where parametric stochasticity is...

15 January 2021 6,950 7 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

What is the state of the drug inside solid lipid nanoparticles (SLNs)?

I am a little confuse with the mechanism of solid lipid nanoparticles (SLNs). The main point of encapsulating drugs into SLNs is because some drugs have low solubility in water. Therefore, SLNs...

01 March 2021 3,703 3 View

How does an antibody have full intact antibody + half antibody?

Hello, I was just wondering how does a antibody have full intact antibody + half antibody? Is it because of the drug conjugation?

28 February 2021 1,577 1 View

How do I choose contrasts in SPM8?

I am learning how to use SPM for PET and PET-MR analysis, but I haven't found any great resources that explain how contrasts work. I have a series of PET images where our hypothesis argues that...

24 February 2021 1,534 2 View

Does anyone have any ideas why drug-resistant malaria is increasing in Southeast Asia even when those drugs are no longer used?

When dealing with bacterial toxins, there are three varieties of microbes that develop in your petri dish: toxic, resistant, and susceptible. Initially, there are only toxic and vulnerable...

21 February 2021 6,084 5 View

What is the most prevalent drug related problem in the developed countries?

Detecting the drug related problems is an important step in the pharmaceutical care plan

21 February 2021 5,421 3 View

No title

19 February 2021 8,647 3 View

Could you please share your experience with me on the type of 96 wells plate for MIC determination: Treated Vs Untreated and Round-Vs Flat-bottomed?

I am working on the MIC determination of various antibacterial agents (both water-soluble and- insoluble) against S. aureus, MRSA, and S. pyogenes. Some guidelines recommend using round-bottomed...

17 February 2021 7,029 3 View

How to improve dissolution of neosome?

I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...

17 February 2021 3,584 1 View

How to determine the drug loading and the drug release capacity of a polymer micelle using UV spectroscopy?

Currently, I am working on PLA-PEG copolymer micelle for the drug delivery system. I have seen several papers where some researcher talks to centrifuge the drug-loaded micelle to separate the...

13 February 2021 5,822 7 View