Can i use the ECM to check the short run equilibrium between univariate relationship in econometrics?

More Ahamed Lebbe Mohamed Aslam's questions See All

In silico can we join two ligands for docking....?

I have performed docking of proteins with two ligands, both ligands show affinity. I want to check the effect if we join both ligands and perform docking

20 July 2024 2,653 2 View

Hi .I have prepared carbon dots for cell imaging and now i lost its recipe is their any method from that i can get its composition?

09 June 2024 2,624 1 View

What is the best medium to isolate the Phytophthora erythroseptica?

Hi, I need your opinion on the best medium for cultivating Phytophthora erythroseptica, the fungus responsible for pink rot in potatoes. Additionally, I would like to know how to achieve maximum...

04 June 2024 8,864 3 View

How does incorporating explainable AI (XAI) enhance trust in critical domain machine learning models, and what challenges emerge in their adoption?

The question delves into the impact of implementing explainable AI (XAI) techniques in critical domains where machine learning models operate. It seeks to understand how the use of XAI contributes...

24 February 2024 5,158 3 View

Is internal control needed for TaqMan Probe-based Real-time PCR Assay?

Hello everyone! I am using TaqMan probe-based Real-time PCR for the detection of typhoidal salmonella. Since I am not concerned about the expression level of gene, I just want to detect if there...

28 January 2024 6,568 2 View

Should I calculate total organic carbon from biochar through loss on ignition Methode?

25 January 2024 9,784 5 View

What is decentralized finance (DeFi), and how does it leverage blockchain technology?

How does Decentralized Finance (DeFi) utilize blockchain technology to reshape traditional financial services, promoting openness, transparency, and accessibility? Explore the key components of...

14 January 2024 3,168 2 View

What is the significance of transfer learning in artificial intelligence, and how does it contribute to improving model performance?

importance of transfer learning in artificial intelligence, focusing on its role in enhancing model performance by leveraging knowledge from one task to improve performance on another.

12 January 2024 5,090 2 View

How to match geometries of two rasters?

I have to use molusce for LULC prediction. For that, i need to match geometries of rasters. I used resampling and clip/extract by mask tools to equalise their cell size and rows/columns. But rows...

22 December 2023 9,781 0 View

How to calculate DNA copy number/ul if I know the DNA concentration in nanograms/ul?

My gene of interest is 312bp in length while the amplicon size (size of my PCR product) is 212 bp. I have cloned it in to pUC57 plasmid (2710bp) to use it as a positive control in qPCR. so while...

12 December 2023 2,570 1 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

E-commerce businesses, COVID-19 and Entrepreneurial Strategies (innovation, proactiveness and risk-taking)?

Hello: I am looking for articles that address e-commerce businesses and COVID-19 survivors, as well as Entrepreneurial strategies that reflect e-commerce businesses. Blessings Evelyn Dempsey

05 August 2024 5,332 3 View

Determining the worth of a point improvement in Hamilton Depression Scale?

Dear readers, Thanks for your attention. I am wondering about the health economic problem of quantifying the value of interventions which a) prevent, b) improve symptom profile and c) ultimately...

05 August 2024 3,246 1 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View