Can I use KH-RT or LISA model for injecting natural gas modeling engine combustion ?

09 September 2017 1 6K Report

I presume KH-RT and model used in CFD (in my case FORTE) is used for liquid fuel injection, which thereafter models liquid gas interaction and finally combustion model comes into the picture.

What to do in case of gaseous fuel combustion modeling?

Mohammad Zandsalimy

You can use a UDF code for your case. It's not easy, but it is possible.

Badges
Science topic

More Sridhar Sahoo's questions See All

What is CGNS error related to Computational Fluid Dynamics Problems ?

I came across many CGNS error codes, which i dont have idea to solve. I got these prblems while solving numerical problem using Ansys FORTE.

07 August 2018 4,397 4 View

Gas spray analysis

How to model a gas (methane-air) jet behavior in a constant volume chamber with quiescent air present over it. what strategy will be used for simulating gas injection? and what will be the...

04 May 2017 4,023 3 View

I am simulating a multiphase flow in a vertical pipe elbow using ansys fluent, am I right regarding the result that I am getting ?

I am varying concentration of slurry and velocity of slurry at bend inlet, the result I am getting is like this: 1. at particular concentration with increase in slurry velocity pressure drop (b/w...

02 March 2015 6,758 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

AUX gas reading problem on QE with full MS and PRM method in one run?

Dear QE-users, In the method where full MS positive mode and PRM mode are used, we always get an incorrect auxiliary gas reading (41 instead of 25). This only happens in this method; other...

06 August 2024 4,953 0 View

The Bigger You Are, the Harder You Fall (some lessons from Dinosaurs)?

Evolutionary fitness is based on an organism’s ability to adapt rapidly to changing environmental circumstances. Large-bodied mammals have been equipped with large brains (and hence a high...

06 August 2024 4,849 2 View