Can I simulate surface enhanced raman scattering using ANSYS multiphysics?

08 May 2015 1 5K Report

Regarding sers biosensor, can I simulate it in ANSYS?

Very Interesting question, similar to my case. Could you check one of the spesial journal in .... (lets me check first....)

Badges
Science topic

More Rana Taha's questions See All

How to extract peaklists from mass spectrometry raw file and do mascot search for my protein in ncbi?

I have a raw file of tandem mass spectrometry (LC-MS/MS) data. I want do online protein databank search for my protein identification and its homology.

30 January 2021 3,081 3 View

How can i save multi medical images after some preprocessing in a file ?

i have multi x ray images after preprocessing on it , i saved them as a vector in file .dat but this file not accepted in next stage (convolution neural network ). how can i save all image in...

27 December 2020 1,369 4 View

What is microbiology and its types,scope?

the study of microorganisms is called microbiology Microbiology is the study of microscopic organisms, such as bacteria, viruses, archaea, fungi and protozoa. This discipline includes fundamental...

13 December 2020 8,287 6 View

How can one calculate Gibbs energy and entropy in ab initio molecules dynamics?

Hello, I've been investigating a bunch of monomers which spontaneously react in water to form a polymer. I would like to know how to calculate the thermodynamics of such a system. On the surface,...

18 November 2020 5,595 3 View

Does anyone know how can I display a aperture or point spread function for MIMO array on MATLAB?

Hello, I am trying to optimize an antenna array for MIMO radar. I want to start by using a MATLAB code to display the aperture and the PSF (point spread function) of the array. Could anyone give...

10 November 2020 6,502 1 View

How to make a solution of resazurin powder ???

I want to test chitosan nanoparticles as antimicrobial against pseudomonas How to use resazurin microtitre assay????

08 November 2020 9,533 2 View

Please suggest me EI compendex conferences with good acceptance rate?

I want to publish a paper at the EI-Compendex conference, please suggest a conference with a high acceptance rate. My field of research is IoT security and cryptography analysis.

19 October 2020 5,365 3 View

What are the recent research direction of Skin Cancer Detection ?

I am doing a research on Skin Cancer Detection. I have read a lot of redundant research papers about the problems which related to the same topic. Therefore, I wish to know the recent research...

04 October 2020 8,628 1 View

Why COS 7 Cells change its morphology to round shape (rounded nucleus and peri nucleus cytoplasm) after Transfection?

I have transfected COS 7cells to express Protein-GFP conjugate, transfection rate was very low (20-30 %) , but the cell morphology changed, many of the cells appear round, (nucleus round too)...

15 September 2020 5,324 3 View

What is the difference between a conclusion and a discussion? How does the conclusion relate to contributions?

Research methodology

12 September 2020 8,410 34 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is there any tutorial for comsol general projections?

Hi, im trying to make a projection in a 3d comsol model. I have a non uniforme chanel and my intention is to get the average tempreture in the y-z cross section and se the average tempreture...

02 March 2021 4,624 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Is it possible to do piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch?

How to do Piezoelectric coupling in ANSYS-APDL or COMSOL between tapered substrate and rectangular piezoelectric patch? Piezoelectric coupling between the rectangular substrate and rectangular...

02 March 2021 9,833 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How can I make stacked bar graph with scatter plot?

I want to make a stacked bar graph with showing each data value as dots. I tried with graph pad prism, version 6, but could not succeed. Does anyone have tried before making such graphs?

01 March 2021 9,383 1 View