Can I run an implicit step after an explicit step in Abaqus?

More Mohamed Balbaa's questions See All

What is the effect of surface roughness on residual stress measurement?

I want to know what is the effect of surface roughness on the accuracy of measurement of RS by XRD. Are there any publicaitons addressing this issue? Also, if it has an effect how to neutralize...

10 November 2018 5,998 5 View

How to define strain as initial condition in Abaqus?

I ran an explicit model in abaqus and I want to create an implicit model with initial conditions of strain, stress and temperature resulting from the first model. How can I perform that? I used...

31 December 2015 9,441 9 View

In Abaqus, how to simulate multi pass heating in DFLUX?

I want to simulate multi-pass moving heat source using DFLUX. I understand that I should use for loop but couldn't get to work, so is there any example or similar case to it?

10 November 2015 7,612 2 View

Is there a source that explains the modeling of Friction in solids in SPH?

I want a source that explains how SPH deals with friction modeling example Coulomb friction. This can be for either Abaqus or LS-Dyna or any other software that explains how they can detect...

03 April 2015 663 2 View

In Abaqus, what is COORDS(1) and how do I change it with time?

I have a subroutine DFLUX and I want to make the FLUX(1) to move so I must change COORDS (1) so should I make a loop and change time from zero to TIME(2) or what should I do?

02 March 2015 2,316 2 View

How can I run DFLUX subroutine in Abaqus?

I want to model moving heat flux in Abaqus so I understand that I must use subroutine DFLUX. I've already linked the visual studio 2008 with fortran compiler and in the job input file I have under...

01 February 2015 5,766 3 View

I need a reference for Hugoniot parameters for Inconel 718?

I want to find the 3 hugoniot parameters ( C, S, Gamma0) for Inconel 718

31 December 2014 4,828 1 View

How can I use renormalized SPH formulation in Abaqus?

LS-Dyna has re-normalized SPH formulation. Is there a similar formulation in Abaqus?

11 December 2014 5,360 1 View

Is there any publication or reference that has the Johnson Cook failure parameters (d1-d5) for Inconel 718?

The Johnson Cook failure is defined by 5 parameters d1 to d5 that are used to simulate material failure in Finite Element

11 December 2014 2,834 3 View

How can I solve tensile instability in SPH in Abaqus?

Is there a solution or work-around for tensile instability in Abaqus?

11 December 2014 9,693 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View

Alireza Jafari Nodoushan

hi dear Mohamed Balbaa

You cant never apply Implicit Step after Explicit Step

you can use explicit result as initial state in implicit step

regards

Mohamed Balbaa

Ok great, thanks

George Papazafeiropoulos

Dear Mohamed,

You can create an annealing step just after the dynamic temperature-displacement explicit step in the model. The anneal procedure is intended to simulate the relaxation of stresses and plastic strains that occurs as metals are heated to high temperatures. The annealing step is an explicit step, so there is no need to have any issues about an implicit step following an explicit step. You can have a look at the following template input file which may be of help to you:

*HEADING

…

*STEP

*DYNAMIC TEMPERATURE-DISPLACEMENT, EXPLICIT

...

*END STEP

*ANNEAL (,TEMPERATURE=)

*DYNAMIC, EXPLICIT (,ADIABATIC)

....

Regards,

George