I am looking for advice. How to prepare bacterial cells for AFM images (live and fixed on glass slide)?

We have a new AFM with a capability to achive high resolution images (up to 50nm). The AFM tips can scan the surface of the object and as well, can penetrate into the object. We also have the...

07 November 2020 2,813 7 View

What are the methods to evaluate autoimmunity in AIRE KO mice?

20 August 2017 4,498 2 View

Why did half of the capacitor charging energy go in parasitic resistance irrespective of resistance value ?

I know half of that energy is dissipated in heat in the resistance of the charging pathway, and only QVb/2 is finally stored on the capacitor at equilibrium I'm just going to lower the resistance...

14 February 2015 362 12 View

Has anyone succeeded tranfecting H9C2 cells?

Which transfection reagent was used? I'm having a real hard time transfecting it.

12 January 2015 5,728 3 View

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What thickness need for ITO to use as conductive layer?

I want to do RF sputtering of ITO on glass substrate using magnetron sputtering. what thickness do i need to make it good conductive layer to use it for PSC. Moreover, whats about thickness of...

01 March 2021 395 3 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

Why is my platinum counter electrode getting dirty during electrodeposition?

I am conducting anodic electrodeposition of MnO2 onto a stainless steel substrate, using a platinum strip as a counter electrode. This is done galvanostatically, with the current held between 5...

27 February 2021 1,829 3 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Why cannot world and community leaders be gentle? Where did ethics of care go?

The whole world is in a mess and paused. We all are tired of seeing hypermasculinized and destructive leaderships all around us. This world has seen enough of the aggressive patriarchal social...

23 February 2021 292 7 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

How does elongation affect the resistance of an electrode?

What are the testing rate for electrodes recommended by ASTM for cochlear implants. I am currently doing the 15mm/min elongatio testing.

22 February 2021 1,515 1 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View