Resource for working with TCAD workbemch
look into the training section of the sentaurus TCAD
step to open training section
1). open terminal
2). source the tcad and write swb
3 ). go to the most right corner of the swb tab named "help" and then scroll to Training
4 click on the sentaurus Workbench and read the full tutorial. enjoy!
Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?
06 August 2024 980 5 View
Hello everyone! I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...
05 August 2024 5,729 2 View
Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...
03 August 2024 5,358 0 View
need to open an account to upload my published papers
01 August 2024 9,255 1 View
All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.
01 August 2024 589 4 View
I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...
01 August 2024 9,227 1 View
Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...
30 July 2024 9,824 2 View
N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.
30 July 2024 7,233 4 View
Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...
30 July 2024 906 2 View
Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...
29 July 2024 7,198 9 View
Hello, I'm newbie to TCAD. I wanna calculate Breakdown Voltage of AlGaN/GaN HEMT. But, my code shows just saturation. Could you please help me how to simulate Breakdown Voltage of my code? And...
25 July 2024 3,738 1 View
Currently, I have created a gate-all-around process using sentaurus tcad and I am trying to measure the noise using the cmos noise code. However, an error occurred during the simulation. The error...
24 July 2024 6,352 0 View
I am getting trouble in studying the effect of channel doping variation in forksheet structure for p and nmos.
08 July 2024 2,074 0 View
The material is SiGe
03 July 2024 1,374 0 View
I already used SiliconGermanium.par why it still error someone can explain this thank you!!
27 June 2024 9,269 2 View
I want to add new mobility model which is not in Sentaurus TCAD .
26 June 2024 9,991 0 View
I can understand that we can use Sentaurus TCAD for designing neuron and synapse. But to implement full crossbar architecture using these neuron and synapse for image classification application,...
16 June 2024 6,879 0 View
I want curve in paper file.But the result of my simulation is that the current is negative, I don't know why?After I tried to change the drain voltage to positive, the curve was right, but it...
08 June 2024 5,351 3 View
I saw an article about using positive charge and negative charge instead of C-H dipole to build internal potential to imitate 2DHG, but my imitation result is not satisfactory, please ask me how...
04 June 2024 8,385 0 View
I am running a gate sweep with transient in sdevice mode in sentaurus TCAD, it is taking too much time, even though the iteration is only 2. How can I reduce the running time?
01 June 2024 4,479 0 View