Can I find someone work on simulation by ANSYS on an aeronautics field ?

More Kamal Abouelmajd's questions See All

Can I do rapid clhoride penetration (RCPT) test on paste? does it has any negative effect? looking for scholars answeers?

29 May 2024 5,438 0 View

What are selective adsorbents for radioactive Cobalt in lower pH condition?

Trace amount of Cobalt-60 is generated in nuclear reactors and needs higher selective separation competing with sister heavy elements, especially Fe-triad. Cobalt has been seen to adsorb on...

28 May 2024 2,167 5 View

How can I draw curve wavelength vs EQE for fixed current of a LED in silvaco tcad. But tonyplot is showing anode voltage instead of wavelength ?

silvaco-tcad

25 May 2024 9,599 0 View

What will be the absorption coefficient(alpha) formula for perovskite oxide materials for band gap calculation?

Different formula i used for calculation but band gap is different for these formula, which formula is correct for my...

28 March 2024 174 3 View

Is this FBS debris in my cell media?

Dear all, I prepared my cell media (EMEM+10%FBS) and another cell media (EMEM+2%FBS+1% Pen/Strep). Incubate the aliquot of the media in 37°C for a few days and saw these. They are not moving and...

24 March 2024 7,496 3 View

Do the fossils exist in Igneous rocks?

This question is very important because its answer is “ don’t and impossible to contain Fossils. This is true and universally 100% accepted, but a new paper published in High Impact Factor (6.5)...

15 March 2024 7,534 4 View

How can I download '' Chemical Equilibria in Soils by Willard L. Lindsay " as a PDF?

Chemical equilibria in soils free download

23 February 2024 3,623 0 View

average growth of jujube tree circles to determine age per year ?

What is the average growth of jujube tree circles to determine age per year?

28 January 2024 2,327 6 View

Why the Fusion-Fission Hybrid System (FFHS) needs less severe requirements on the plasma confinement quality?

I would like to know why an FFHR's plasma has no need for high power amplification performance.

22 January 2024 6,623 1 View

XRD peaks shifting?

I incorporated magnetic nanoparticles into MOF and the MOF XRD peaks shifted towards the left side. What should the possible reasons be?

22 November 2023 4,151 2 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Tangential stiffness option in ansys workbench?

I am not able to find how I can provide tangential stiffness in ansys workbench The normal stiffness option is there. But how I can enter tangential stiffness I have read somewhere tangential...

29 July 2024 2,032 2 View

How to Import Blade geometry from CAD file in ANSYS design modeler?

Hello. I have the geometry of a blade in CAD file (stp) and I want to prepare the blade for meshing with turboGrid. I must import this file into designModeler and then transfer to the...

27 July 2024 356 3 View

Why my simulation results are showing too much deformation compared to experimental result?

I performed fea on tensile dog bone specimen using ANSYS static structural and also tried using ANSYS explicit dynamics. In experimental result the load is 500 N and deformation is 0.6 mm...

13 July 2024 3,631 4 View

Can I transfer the 3D file from Matlab to Ansys or Abaqus?

I have a 3D output in the figure section of Matlab, does anyone know a way to transfer it to Abaqus or Ansys? Or in what format should I save it so that these analysis software can analyze it?

09 July 2024 9,226 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

How to import STL format into ANSYS APDL?

Hi everyone, I want to import an STL geometry (surface meshed with 2D meshes) into ANSYS APDL. After importing, I also want to mesh the structure with SOLID187 elements to convert it into a solid...

25 June 2024 4,286 4 View

What is the difference between the rotational velocity and cmrotate command in ansys?

I am trying the simulate the drum brake squeal in ansys. For giving the rotational velocity to drum what should i use the Rotational velocity or CMROTATE command.

24 June 2024 5,125 0 View

Next APDL command to get eigenvalues?

I need to get the eigenvalues after a modal analysis in ansys workbench. Is there any next APDL command that will get the required result.

20 June 2024 1,668 0 View

How to compile a udf in Fluent to import hourly weather data and update the boundary condition based on it ?

Hello all, I've compiled a udf which reads velocity data with corresponding time stamp from a .csv file using DEFINE_ON_DEMAND macro. Then, I use DEFINE_PROFILE to define an inlet velocity profile...

14 June 2024 6,480 0 View

Mostak Ahamed

Yes, you can find someone to work on aeronautical simulations using ANSYS software. There are several freelancers, engineers and consulting companies on sites like Upwork and Freelancer that specialize in this type of work. You can also search for companies that offer engineering consulting services in your area that provide simulation services.

Kamal Abouelmajd

Mostak Ahamed Thank you