Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to calculate the annealing temperature of a primer pair?

I have to amplify a gene and my primers just reached. The Tm for Forward primer is 64.2, and that of reverse primer is 65.5. Can some one suggest how to get the best annealing temperature? Thanks...

01 March 2021 360 7 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

The reason that the culture of white fungi Contamination with green mold(Trichoderma), the culture autoclave at121 for 15 min. What is it?

Is the period to autoclave not enough? The inoculation in a hood and flame and UV and alcohol.

27 February 2021 9,356 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

Does different dilution factors affect negatively on NH3 reading ?

I have a sample of treated water sample & asked to obtain ammonia conc. in sample using a machine with 5-25 ppm detection range. However, upon testing with different dilution factors, all...

27 February 2021 8,483 3 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

How does the gut microbiome affect the fibrotic process within the liver?

and Can the gut microbe be used for the treatment or diagnosis of liver fibrosis?

02 March 2021 557 2 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

How to indicate the degree of litter decomposed by microbes?

Any technique could detect the degree of litter decomposed by microbes? Or any indexes could do this job? I want to split the contribution of microbes during decomposition, so any suggestions...

23 February 2021 1,362 5 View

In frequency domain alpha band(8-16hz), beta band(16-32hz), gamma band(32-64hz), sub-band(64-128hz) are same as LL,LH,HL,HH in wavelet decomposition?

I am working on single trial motor imagery data i.e. EEG data. I am following a paper which has a dataset from BCI challenge IV (dataset 2b). After removing noise and extracting all the data from...

23 February 2021 5,503 1 View

Can I arbitrarily take a cycle number of 40 for the gene that was not expressed at all in qPCR results calculation?

I ran RT-qPCR for a control and a treated group and it appears that my gene of interest was not expressed at all in any of the subjects in the control group. So I was wondering if I could...

20 February 2021 6,243 10 View

Can I get information about research laboratories that are currently having in culture, internationally/locally standardised microorganisms?

Microorganisms of interest include; E.coli; Salmonella typhimurium; Pseudomonas aeroginosa; Streptoccocus pneumoniae; Staphyloccocus aureus and Candida albicans. Locations closer to Port...

18 February 2021 6,500 3 View

Can bio-decomposer be a successful alternative to reduce residue burning?

To maintain the proper crop plan most of the times there is not enough time to make the field ready for the next crop. In this particular context , can bio-decompser be a solution? What about...

16 February 2021 7,068 24 View

Does anyone know if the Quantstudio 3 qPCR machine requires a passive reference when Using SYBR? I ran a qPCR and got the plot in the attached file.?

I know that my target is in my sample as I extracted it from cell culture myself. These plots show some amplification. The first one seems O.K for the first 36 cycles but then collapses at the...

14 February 2021 2,809 2 View

Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View