1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

How to get nanocomposite of PEEK with Zirconia ?

Need a lengthy PEEK with Zirconia based nano composite of 180 mm length. Which method is possible? Tried injection molding no proper mix. Solvent casting process is also very costly. Kindly anyone...

13 December 2020 4,329 5 View

How can I get eggs of an univoltine casebearer moth for a threshold study?

I am planning to conduct a cage study to determine a critical density of an univoltine casebearer moth in red clover seed crop. This requires to release first instar larvae in the cages with the...

02 November 2020 6,577 3 View

Bio-intensive cropping systems can reduce the environmental foot print?

The adoption of bio-intensive cropping systems has the potential to reduce environmental footprints without compromising the economic gain per unit of resources.

12 October 2020 2,625 7 View

Application of Polyhalite changes the nutrients chemistry in soil?

Polyhalite is a multi-nutrient source, its application assume to be changes the soil biology and nutrients chemistry on long term basis

12 October 2020 6,685 3 View

How to recycle Sodium Iodide?

Hi, I am using sodium iodide to separate density carbon fractions of my samples. I want to recyle it for further uses. While searching I only get the process to recycle sodium polytungstate (at...

20 September 2020 9,556 2 View

Purpose of keeping the rocket nozzle assembly inverted, for Actuator-In-Loop simulations ?

For Actuator-In-Loop simulations, why are the rocket engine nozzles along with the thrust vector control assembly (including the actuators) kept inverted on a platform like in the attached image...

14 August 2020 8,652 2 View

How to add attenuation model and spectral ordinate in R-CRISIS?

Hi Everyone I am using R-CRISIS for seismic hazard map creation. I know how to use the given attenuation model in R-CRISIS but I want to use an attenuation model from a published article. How to...

23 July 2020 5,265 1 View

Is there any python module is available for statistical seismology?

Could you suggest any python module that is made for dealing with statistical seismology?

29 May 2020 9,068 6 View

What do you think about the scope of AI based teaching-learning provision during this COVID-19 pandemic?

COVID 19 has put its worst impact in many sectors of our life. Education is one of these. Students are staying at home and missing the opportunities of learning from a real classroom filled with...

19 May 2020 4,581 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View