Help: How to install Skynet?

SkyNet is publicly available as an open-source software at https://bitbucket.org/jlippuner/skynet. However, i can not install it on my computer? Have anyone met the similar problem? First, CC=icc...

20 September 2020 6,912 16 View

How can i know a small molecule or drug can penetrate into cell membrane and come into cytoplasm?

i want to select drug which can cross cell membrane and come into cytoplasm. how can i know? which property of drug is important? best

16 April 2020 3,926 3 View

What are the techniques to validate qualitative research instruments?

I am currently doing a quasi-experimental research. I have decided to use both qualitative and quantitive methods in collecting the data. For the qualitative data, I have an observation card and...

08 October 2019 4,007 5 View

How a researcher can validate his upcoming research instruments?

I will be conducting an action research in one of the schools at my place of working and my supervisor has asked me to validate my instruments before I can use them during the research process. I...

11 December 2018 1,355 3 View

What is a best way to immobilize RGD peptide with electrospun nanofiber?

I synthesized the nanofiber via electrospinning but need to find a best way to immobilize RGD peptide (Arg-Gly-Asp) onto naofibers.

03 September 2018 8,448 1 View

In order to elicit an action potential, how many synapses should be activated?

It has been estimated that one neuron may have thousands of synapses. In physiological condition, it seems like one pre-synaptic neuron can only elicit small EPSP in a post-synaptic neuron. How...

07 November 2017 9,079 11 View

Why single crystal 6H-SiC has higher thermal conductivity(490W/(m.k) than that of copper(401W/(m.k))?

Heat is dominantly transferred via phonon in SiC while free electrons and phonon both contributes to heat transfer in copper, why SiC has higher thermal conductivity than that of copper? Is that...

17 August 2017 8,457 3 View

Can cell grow on a pure minimal salt media (MSM) without any carbon source?

30 May 2017 7,995 11 View

Can a capacitance type transmitter to be intrinsically safe type also?

If no, what is the difference between capacitance type transmitter and intrinsically safety type transmitter?

15 May 2017 2,666 2 View

How can I make sure there is no back flow in the system?

Kindly find the image attached. Pressures of the fluid in A, B, C, D and E are difference.If certain pressure is too low, how can I prevent the back flow from occurring? By arranging the pipe of...

11 May 2017 1,756 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View