How to figure out easily the right journal with the right scope for your paper?

According to my experience most of the selected journals during paper submission are based on journal text matching suggested results from Springer, Elsevier,,,Etc. then the manuscript happened to...

01 March 2021 1,786 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

Is there any software or formula for sample size determination by using sensitivity and specificity?

I want to conduct research on the diagnostic performance of some tests. I want to calculate sample size by using the sensitivity and specificity of the test in the previous studies. So Is there...

23 February 2021 619 5 View

What is the best way to track bird migration?

Migratory birds are globally scattered. What should be the ways to track them? Except ARGOS. Elaborate.

25 January 2021 2,355 4 View

How i can reduce the number of atoms using Vesta ?

I'm a new Vesta learner, I have downloaded cif of Ch3Nh3PbI3. Total number of atom in chemical formula for Ch3Nh3PbI3 is 12. But when i convert this cif to poscar file using Vesta, total number of...

14 January 2021 5,733 11 View

How to determine the sample size for ANOVA in GPower?

Hi, I am going to execute an experiment with the four categorical variables (A=2 levels, B=2 levels, C=2 levels, D= 5 levels) and one dependent continuous variable. There are total of 40 groups...

19 December 2020 3,600 4 View

How to calculate the replacement cost of battery?

As battery needs to be replaced after the specific charge and discharge cycles mentioned in the datasheet. If we have the time series data of battery power and energy capacity, then how can we...

01 December 2020 3,433 3 View

Can anyone please elaborate the relationship between charge and discharge cycles and battery lifetime?

I am designing the optimal HESS capacity for the renewable system. I have to select the cutoff frequency of low pass filter to divide the low and high-frequency components. charge and discharge...

05 November 2020 8,397 3 View

How to select the frequency range in MATLAB Wavelet toolbox?

I have a continuous, time-domain noisy signal and want to decompose into low-frequency (LF) and high-frequency(HF) components using Wavelet Toolbox. But, I am unable to select the frequency range....

29 October 2020 5,219 5 View

How can I retrieve information of viruses reported from a particular region/country ?

Dear All, Can anyone please guide me on how to get information (sequences) of plant/animal viruses from a specific region ? Looking up the published literature is one way but its time-consuming,...

19 October 2020 3,958 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View