Saline droplet evaporation with DPM in Fluent?

I want to simulate the evaporation of micron size saline droplet in room temperature emitted from mouth using Fluent. The question is how to define the saline droplet in fluent? I define...

30 August 2020 3,342 7 View

Parameters for Antoine equations?

I need the saturation vapor pressure of FeO, CaO, MgO, SiO in the temperature range of 1500~2000K. Usually, it can be expressed in the form of the Antoine equation (log10 P = A+B/(T+C)). Could...

28 August 2020 2,093 2 View

How does a Grid-tied solar inverter back-feed surplus solar power on to the grid?

Hi, I am trying to find out what adjustments does the grid-tied/on-grid solar inverter make to send excess solar power back on to the grid. Basically how the inverter change the direction of power...

04 August 2020 7,594 8 View

How do I calculate ionic current with Gromacs?

21 November 2015 9,170 7 View

Can 293T cells be used to make recombinant vaccinia virus?

I'd like to generate a recombinant vaccinia virus by transfecting a plasmid and infecting virus simultaneously. I've been using U2OS cells to propagate vaccinia virus. But the transfection...

25 September 2013 2,386 2 View

Is there any method available that clearly differentiates between different prostaglandins (PGE2; PGF2a; PHG2 etc.)?

I want to know if there is any method available to clearly differentiate between different prostaglandins (PGE2; PGF2a; PHG2 etc.). I am looking for a method such as thin layer chromatography...

25 September 2012 5,275 2 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

How to compare two groups with only two measurements?

Hiiiii everyone! I have an enquiry on statistical analysis. I was looking for many forum and it's still cannot solve my problem. I want to compare means of two groups of data but only with two...

03 March 2021 8,796 3 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence?

I am on the lookout for the Enhanced Yellow Fluorescent Protein (Aequorea victoria) DNA sequence. Does anyone know where I can find it? Thank you in advance

03 March 2021 3,568 1 View

What kind of fluid could I use for a pitfall trap that also does not invalidate molecular testing?

Hi, I want to start testing pitfall trap to obtain ants samples, but I need to conduct molecular analysis on those insects. So, what kind of fluid can I use? Ethanol expires too early and I need...

03 March 2021 5,978 5 View