Algorithms to solve multiple objective shortest path problem.
articles or publications on multiple objective shortest path problem.
non dominant algorithm for multiple objective shortest path problem.
I think the expert you need to read from is Dr. Andrea Raith. I have attached two of her
articles about bi-objective shortest path problems, finding OPTIMAL solutions.
I think, you should pay attention also to genetic algorithms. They well work in multicriteria tasks.
Read my PhD thesis also which based on ACO. See the following link:
http://bura.brunel.ac.uk/handle/2438/4282
Please read the following paper also
http://www.sciencedirect.com/science/article/pii/S2210650215000188
PDE value for Tert-Butylamine
24 July 2024 1,166 0 View
What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?
08 July 2024 7,464 1 View
How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...
08 July 2024 6,609 2 View
what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?
08 July 2024 7,869 1 View
Hello, recently i am an issue swith cloning where I am using the subclone method to insert my gene length is 1.5kb and my vector(pMAL-c6T) is 5kb I got the colonies which i screened through the...
04 July 2024 7,977 2 View
Context In the realm of cybersecurity, Transport Layer Security (TLS) is widely used to secure communications over a computer network. Despite its robust encryption mechanisms, TLS is still...
19 June 2024 6,595 3 View
Hi , I am facing difficulty in simulating MFMIS NC FET. Kindly help. How to define buried metal in Sentaurus TCAD?
27 May 2024 3,208 0 View
I would like to calculate the gear wheel and gear tooth deformation due to rotational speed? The gear shaft is mounted on hydrodynamic bearings. What are the boundary conditions need to apply?...
21 May 2024 8,067 0 View
What is full wave simulation in antenna ? How to simulate in CST Studio software? Can anybody explain.
20 May 2024 5,224 3 View
Can anyone explain The overall size of the proposed antenna is only 1.34λ0 × 1.32λ0 × 0.014λ0.? What does it Mean?
20 May 2024 9,177 4 View
Could you recommend some articles on Urban Transportation System optimization and Innovation?
13 August 2024 2,595 3 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
Are there any statistical methods to justify your sampling technique using SPSS or AMOS?
05 August 2024 9,153 4 View