Can anyone help me with cerebrospinal fluid cytocentrifugation? What are the best speed/time? Do I need to add 22%BSA or autologous serum?

More Guilherme Dias de Melo's questions See All

PACYC PCR not working after several attempts. Would anyone have any suggestions?

So, I have been trying to run a pACYC PCR which will be used later on for a Gibson Assembly. However the PCR is not working. I have already tried gradient PCR and changing extension time; however...

02 March 2021 1,146 2 View

Quantifying leaking DNA from bacteria - what's the secret?

Hi, all! I need to determine if my treatment causes membrane damage in bacteria (S. aureus and E. cloacae), but I cannot use a fluorescent probe such as PI and similar ones because my compound is...

24 February 2021 2,006 2 View

Please let me know how to remove mycoplasma contamination from cell line?

I am facing a problem in maintaining the cell line of HepG2 and HepG2.2.15. I have used plasmocin Tm treatment (Invivo gen) Cat.#ant-mpt Lot #MPT-41-01 for more than a month. I have also used...

21 February 2021 6,046 4 View

Western blot protein of interest falling at a lower weight than expected?

My protein of interest is DAGLa (115 kDa). We received the antibody for this from another researcher who reliably shows bands at this weight. We do see a light banding at this weight, but the...

11 February 2021 6,009 3 View

Which Journals would you advise to submit a Letter which briefly talks about neurosurgical treatment of neuro-oncological patient during Sars-COV-2?

Possibily not an open access journal which does not add any publishing costs once being accepted. Thank you in advance

09 February 2021 717 6 View

Are there any differences between setting automatic or manual number of measurements in DLS?

When doing measurements in DLS (either size or zeta potential), I have the option to input an automatic number of measurements or to set it manually. My question is: is there a drawback in...

08 February 2021 9,423 6 View

Sample Size for Quasi-Experimental Quants using one-tailed t-test?

Hi, sorry I'm stumped. I'm going to do a study on the leadership styles (using the MLQ Form 5X) of minority women administrators in medical schools. How will I calculate the sample size? Thank...

30 January 2021 2,865 4 View

Can you do Ponceau staining after loading control for Western Blot?

Hello everyone! I forgot to take a picture of my Ponceau stain prior to starting my first round of primary and secondary antibodies. I'm currently doing my loading control now and was wondering...

25 January 2021 757 3 View

What is the correct way to apply a Design effect for sample size calculation when the sampling method is linear systematic random sampling?

When we are doing sampling by means of simple systematic random sampling,how do we calculate the design effect for use during calculation of sample size for our work?

20 January 2021 5,328 3 View

Anybody to help me with Code source for DOUBLE CONCAVE FRICTION PENDULUM BEARINGS Please?

Hello, would you please share the codes for Base Isolation of structures using Double Concave Friction Pendulum Bearings? I am doing a related research but as I am just a beginner in MATLAB, I...

18 January 2021 6,683 1 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Does anyone know HRM channel in a 2 plex QIAGEN Rotor- Gene Q qPCR can be used as a separate channel?

I am going to have 3 different probes in my qPCR work that I am going to do. But I realized that the machine we have in the lab is a Rotor-Gene Q 2plex HRM Platform, saying it has green, yellow,...

01 March 2021 8,544 1 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Which is better medicine or food in obesity?

Preference in terms of the scientific aspect

28 February 2021 796 2 View

Gaber Ramadan

Hi Guilherme

Concentrate the cells using regular centrifuge (500 - 650 rpm) for 3- 5 minutes. Then, resuspend in 0.5 ml saline. Finally, use Cyto•Fluid Fix™ and cytospin slides as the cerebrospinal fluid has sparse or no cells. Centrifugation at 650 rpm for 2 minutes. Stain after draying.

Arjan Tibbe

Did you ever consider filtraton instead of cytospinning? Filtration simplifies the procedure considerably with and has a very high yield. Take a look at www.vycap.com to find out if filtration is working for your purpose.