11 December 2020 1 8K Report

My question is how to find system-specific ionization potential (IP) tuned value to improve the description of the excited state for a functional in the TD-DFT calculation.

Do I need to run any script for the same?

More Kalyan J Kalita's questions See All
How to check leakage current of Si-SiO2 wafer?

I want to use the n-type Si wafer coated with a 300 nm SiO2 layer for the OFET device, but for that, I have to check the leakage current of the dielectric layer. how?

07 February 2024 4,115 2 View

What will be the quality of Al2O3 layer in OFET device fabricated through RF Sputtering?

This question is related to OFET devices. Please suggest some answers to this question.

07 February 2024 8,067 0 View

How to extract velocity data of a moving object from a simulation done in Ansys Fluent?

Hello Everyone!! I am currently working on a model for renewable energy harvesting using ocean wave energy in Ansys fluent. I have applied a dynamic mesh and compiled the UDF for motion of a...

30 January 2024 8,896 1 View

How to remove negative volume error in Ansys fluent dynamic mesh?

Hello Everyone!! I am currently working on a model for renewable energy harvesting using ocean wave energy in Ansys fluent. I have a design ready along with a UDF for a moving component. But when...

08 October 2023 5,531 5 View

How to solve highly non linear coupled eqn. ?

send me a matlab program

22 August 2023 7,317 2 View

What is the concentration of antibiotic for PCR 2.1 TOPO cloning?

Ampicillin 50ug/ml is what specified in the kit, means should I use 5 grams of ampicillin for one liter of LB agar?

15 August 2023 7,603 2 View

How can we isolate exopolysaccharide content from cyanobacterial strains?

Is there any method for isolating exopolysaccharides (not the total Carbohydrate) from cyanobacteria?

06 August 2023 4,234 2 View

Where do i get elastic compliance constants required for the orthorhombic crystal structure?

USDM and UDEDM model of Williamson Hall plot, elastic constants are required to calculate the Youngs modulus which further usefull in calculating stress and deformation energy density. I am...

12 June 2023 1,425 0 View

How can I find or estimate the species specific parameters α and β for application in Beta-poisson model for QMRA?

I am trying to estimate the QMRA for three species of bacteria using beta-poisson model. The literatures that I followed have not reported the α and β values for these 3 specific bacteria, while α...

27 May 2023 5,692 0 View

Q-Exactive calibration error for Mass resolution Dependency too high, can anyone help?

Hi, After performing my annual cleaning on the QE and calibrated, it as passes the positive cal but when performing the basic (negative) Analyzer accuracy it has failed for Mass resolution...

08 January 2023 2,206 1 View

Similar questions and discussions
What is saturation solubility of insulin in saliva?? I need it to know sink condition ?

..

05 August 2024 4,407 0 View

How to increase protein lysate concentration?

I am trying to prepare samples for IP. The pellet size is good and I am using 1% Tx-100 and using a syringe to further lyse the cells and maintain protein-protein interactions. I keep having a...

01 August 2024 7,199 1 View

How do we pick data for determination of Validation Acceptance Criteria?

Hello, colleagues! There is commenting open for new upcoming edition of USP 1033. Validation target acceptance criteria is now different from what it used to be and it doesn't include Cpm....

23 July 2024 7,292 3 View

What do you think are the key challenges that need to be addressed in the future development and application of these three devices?

Continuous glucose monitors (CGMs) help patients and doctors make more timely management decisions by monitoring blood glucose levels in real time. An insulin pump provides continuous insulin...

07 July 2024 7,742 0 View

How can I improve the purity of NPC cultures derived from human iPSCs during neural rosette selection?

Hi everyone, I've been working on differentiating human iPSCs to derive a pure and uniform culture of neural progenitor cells (NPCs). However, I'm encountering a significant issue during the...

01 July 2024 1,012 1 View

GC-FID Resolution Issue ?

I am working on CO2 photoreduction. During my work, I am facing a problem with my GC-FID analysis. Some of my analyses are showing a peak shape resembling a hump or a steep decline in the region...

21 June 2024 8,623 5 View

What are some reliable methods to measure the concentration of H2 gas at ppb levels?

We'll have vials in which we expect H2 generation to occur. Over the first few days, the amount of generated H2 is expected to be at ppb level. GC (+ TCD) detector is best when your H2 level is...

18 June 2024 254 3 View

Question about ELISA with the "Cattle IGF 1 (Insulin like growth factor) ELISA Kit" Cat: ELK5630?

Dear fellow researchers, We are conducting an ELISA with the "Cattle IGF 1 (Insulin-like growth factor) ELISA Kit" (Cat: ELK5630). Samples and reagents were prepared following the instruction...

13 June 2024 9,473 0 View

How can I get to the parent molecule name by inputting the MS fragments values?

I did GCMS/MS, LCMS of my sample of interest. I got Mass fragments in ionization process. Now facing issues to get the parent molecules name/formula. Due to complexity of sample (its a mixture of...

01 June 2024 1,056 4 View

How is a proton generator made?

How is a proton generator created? Hydrogen seems to be the easiest method, using He gas and an ionized attraction means. But has someone achieved this?

31 May 2024 5,766 0 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close