Where do i get elastic compliance constants required for the orthorhombic crystal structure?

13 June 2023 0 1K Report

USDM and UDEDM model of Williamson Hall plot, elastic constants are required to calculate the Youngs modulus which further usefull in calculating stress and deformation energy density. I am struggling to get these values.

Badges
Science topic

More Kalyan Chavan's questions See All

What pH condition required to coat APTES on silica coated Fe3O4?

It's a hydrolysis reaction, which may produce by either acid or base-catalyzed reaction. so can anybody help me with this, which condition is suitable for this reaction?

26 February 2021 1,760 8 View

What condition required for coating of Fe3O4@SiO2 by using APTES?

I tried coating Fe3O4@ SiO2 by using APTES in 5% water-ethanol but it is not coated. Kindly suggest a solution for it. Thanks

24 February 2021 5,992 4 View

I want to simulate a system containing protein and heavy metals; which force field is most reliable for this purpose?

The protein I want to simulate has multiple heavy metals. I wanted to know which force-field I should use with GROMACS to achieve this. Most importantly, do the latest updates in the force-field...

16 February 2021 2,420 1 View

Under what conditions absorption and excitation spectra of a same species can be different?

I took absorption and excitation spectra of a same species in the same solvent. Ideally I should get the excitation spectra almost similar to the absorbance spectra. But I got the excitation...

13 December 2020 8,965 2 View

How to calculate Transport properties using impedance spectroscopy for polymer nanocmposites?

Hello Friends / Teachers . I have obtained data from hioki impendence analyzer IM3570 But i am not understanding how to calculate Transport properties for polymer nano composites .

24 July 2020 5,611 2 View

Measurement of Gain of a CP antenna?

How do I measure the gain of CP antenna inside an anachoic chamber? What should be the reference antenna, I mean it should be LP or CP? What is the procedure of measurement?

17 November 2019 336 6 View

How to obtain the sputtering yield of different species in Quaternary sputtering target?

we have prepared the CZTS thin films using single target in RF sputtering. which formula should i use to obtain the sputtering yield of different atoms such as Cu, Sn, Zn . is it possible to get...

15 October 2019 1,699 6 View

How to extend conference paper into journal paper?

I would like to know , what are the possible ways to extend conference paper into journal paper? My work is in the area of natural language processing

22 September 2019 1,246 3 View

How to obtain the crystallinity and strain in the thin film using RAMAN shift?

we have deposited the semiconducting thin film (CZTS) using sputtering. is it possible to obtain the crystallanity and strain in thin film using RAMAN spectra? which formula should i use for that?

09 September 2019 8,088 1 View

Is it possible to get different RAMAN shifts for the same sample deposited by different process parameters?

I have deposited CZTS by RF sputtering at different temperatures, pressures and powers. In RAMAN analysis i am getting peaks at 334,337,330 cm-1 is it possible to observe these kind of shifts due...

04 September 2019 5,898 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

What is the most suitable server for predicting protein structures in bacteria?

I have used the i-Tasser several times, however it has been unavailable for several days. I tried the swiss-model, but the output was not very pleasant due to the model used. Is there any other...

28 February 2021 4,521 3 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View

How to build fluid structure interaction simulation for elastic ring squeeze film damper in COMSOL?

22 February 2021 5,408 1 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

Build an orthogonal box in ASE?

Hello, I was wondering the best way to build an orthogonal box filled with a defined crystal structure in ASE. I know it could be easily done in LAMMPS, but I guess it is also doable in ASE. The...

21 February 2021 5,899 4 View

How to do a surface treatment of uncoated TiO2 with polymer?

Basically, I would like to know how to treat or coat on the uncoated bare TiO2 (Ti-OH rich) surface with polymer which has anchoring groups in the polymer structure like trimethoxygroups. What is...

21 February 2021 4,657 6 View

How to model rupture in geogrid in abaqus?

Hi researchers I wanna model tensile test on geogrid in abaqus, so I added displacement to one side of geogrid and the other side of geogrid is constrained completely, everything seems normal but...

19 February 2021 2,195 2 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View