Can anybody help me draw graphene and graphene oxide using ACD/Chemsketch?

More Vijayarangamuthu Kalimuthu's questions See All

How to do photocatalytic degradation of dye experiment using hydrophobic powder sample?

How to do photocatalytic degradation of dye experiment using hydrophobic powder sample. Issue here is that hydrophobic powder start floating on the surface of the aqueous dye solution. which...

11 December 2017 6,678 3 View

For gene optimization what must be the supported file format to be loaded in the Eugene software at load genome option?

I need to load Chlamydomonas reinhardtii genome (optimize the gene based on the codon usage of Chlamydomonas reinhardtii)

04 March 2015 9,380 1 View

Can someone provide a procedure for cleaning copper for CVD graphene growth?

I need a complete procedure for making single layer graphene using CVD and copper foil (25 um thickness). Particularly concentration of solution used for cleaning like acetic acid or HCl etc

28 April 2014 8,670 11 View

What is ratio of both PMMA (Polymethyl methacrylate) and anisole for making PMMA resin used for coating on graphene surface?

PMMA for covering graphene to etching copper, something like 950 PMMA A4 from Micro-Chem

11 November 2013 6,817 1 View

What is the appropriate value of interfacial area density applicable to a porous artery?

We are doing heat and mass transfer analysis when blood flows through a porous artery. We apply ANSYS CFX for the simulation analysis. We want to fix interfacial area density between two phases...

15 December 2012 9,511 3 View

Response surface methodology (RSM) , ANOVA and Jar test

I have been doing a research on using RSM to optimize coagulation - flocculation process , by using ANOVA to validate the optimisation , 4 independent variable and 2 responses. I am confuse...

01 January 1970 5,948 2 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Should we reduce the standard unit of length to 0.31951540592 meter ?

The reasoning behind this question is to align the ratios of the proton potential in energy per charge to the speed of light in distance per time. As these two dimensions appear to be related,...

27 February 2021 947 7 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

What program can I use to caclulate dipole moment efficiently and without the need of excessive computation?

Hi, I am a third year chemistry undergrad doing my group project in which I need to predict the HPLC retention time of 20 aromatic molecules. to do this we require the chemical properties of these...

24 February 2021 1,384 3 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Saira Bano

What kind of help you required?

You can draw in chemsketch and paste that structure in inkscape, where you can modyify further

Vijayarangamuthu Kalimuthu

I want to have optimized 3D structure, but it use to say you have more than 250 atoms something like this.. so how can have big sheet of graphene with oxygen on the surface which is aligned vertical.