Can any one suggest a paper on "Effect of Carbon on structural integrity of dissimilar welding of low alloy steel and austenitic stainless steel"?

More Ravikiran Kopparthi's questions See All

How to understand the changes in morphology w.r.t change in xrd peak intensity and shift in 002 peak of graphite?

My starting material was natural graphite flakes, xrd showing the standard peaks. Post processing my sample has the distinct 002 peak (sharp) but with slight shift to the left side and significant...

06 May 2023 4,140 4 View

Which matrix need to choose for Calculation of Mutual coherence in compressive reconstruction?

My signal is X. X has sparsity in the DCT domain. X = Ψ * coeff. Then the compressed signal is Y= Ф * X. At the reconstruction algorithm, Reconstruction matrix is A= Ф * Ψ . To calculate...

17 July 2019 9,684 3 View

What will be the effect of groove design on residual stresses?

By changing groove angle and groove geometry, can we expect any differences in residual stresses in a weldment?

18 March 2018 3,471 7 View

Looking at both economic and scientific aspects, is it acceptable to go for a narrow gap welding, for a 25mm thick joint?

02 March 2018 8,270 2 View

How can I plot dielectric data with frequency with the help of Cole Cole plot?

I have the impedance, resistance, reactance data with frequency variation.

20 July 2014 1,626 8 View

What are the manifestations of the oil/gas/water contacts in subsurface on the logs, seismic sections and others?

Finding different contacts in hydrocarbons.

11 March 2013 5,777 8 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

How should operational parameters be selected when developing a pore-free laser welding technology?

There are three operating parameters - the laser power, the diameter of the focus spot and the scanning speed. It is necessary to obtain a seam of a given depth without pores. What parameter...

27 July 2024 7,168 2 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

V V K Lakshmi

Influence of graded compositions and carbon diffusivities in buttering on structural integrity of dissimilar metal welds in journal material science and engineering

Materials Science and Engineering: A

Peter Mayr

Look for John DuPont in International Materials Reviews

Mohammadreza Aali

I think this paper is useful.

Temperature fields and residual stress distributions in dissimilar steel butt welds between carbon and stainless steels.