Why do my MCFs not form monolayer?

Hello, I am looking for some expertise on culturing MCF7s. I purchased them from ATCC and I have been following all media and culture conditions. Media is EMEM with 10% FBS and 10ug/mL of...

27 February 2021 3,904 2 View

How does charge on working electrode changes with rising potential?

During performing CV of a GCE or modified GCE, we rise the potential in the first half of the cycle and reduce it in reverse half. During the first half, what is the nature of charge on GCE or...

25 February 2021 7,994 3 View

Can we measure porosity of a composite by DSC (heat flow measurements)?

In the DSC conducted for A and B (image provided). B is a derivative of A. Can I conclude that the porosity of composite B is more than A, Since the heat flow is decreasing with increase in...

26 December 2020 9,104 3 View

Can I carry out LC-MS for AuNPs?

Will it be helpful to know the nature of stabilizers used in synthesis of curcumin (if it has polymerized or not). Any specific measures to be followed to carry out these kind of experiments?

15 December 2020 2,283 4 View

Why I am not getting UV absorbance peak of AuNPs?

I synthesized Au deposited on graphite electrochemically by using chronopotentiometry. How much ever I tried I couldn't get UV absorbance peak of AuNPs in any number of solutions I tried? But when...

20 October 2020 2,040 5 View

What psychological affect does age have on death penalty?

The debate about the death penalty have been one that has been around for years, it is something that has always interests me . For my major research project to finalise my degree as a student, I...

04 October 2020 6,757 9 View

Can i use surfactant C-TAB in extraction and detection of the aminaphthalene sulfonates by HPLC technique?

In the detection of Aminonaphthalene sulfonates the quaternary ammonium salts like Tetrabutyl ammonium bromide ,Triethyl ammonium acetates are used so the C-TAB being an quarternary ammonium...

21 September 2020 9,636 1 View

How to fill the gap between two contigs?

Hi everyone, We have sequenced genome of data of a comparatively less studied species using Pacbio long read sequencer. Now after initial assembly we compared the contigs with previous version...

25 June 2020 3,442 3 View

Which motion analysis software can give me this functionality to create some sort of kinematic model?

25 October 2019 2,556 6 View

Automation in ansys with load location as parameter?

What is the best way (in a way that ansys runs each job sequentially without manual command) to solve several problems (say 1000+) with exact same geometry and other solution parameters but...

07 October 2019 2,073 3 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View