Boundary condition for inlet and outlet for a tesla turbine for simulation in fluent?

More Vedant Kumar's questions See All

Gas Turbine Blade Cooling simulation using ANSYS Fluent 18.2. Why does it show divergence in AMG solver?

I am currently working on Gas Turbine Blade Cooling design where inside a turbine blade a cooling channel is incorporated. The cooling channel is made of a single pipe system which is recirculated...

06 July 2019 4,315 2 View

How to calculate pressure drop across n number of perforated discs?

Relations for calculating pressure drop for flow across a single perforated disc are widely available. However if there are n number of discs placed in the direction of flow, how can we calculate...

02 March 2018 5,751 0 View

Pressure at duct inlet

Is there anyway I can decrease the pressure at the inlet of a Converging-Diverging duct while maintaining same far upstream flow conditions? I mean to say that I want to make changes in the duct...

05 June 2017 5,530 4 View

Propeller vs Turbine

Can I model a propeller as a turbine just by changing the value of coefficients like loading coefficient, thrust coefficient,etc to negative given that they rotate at same RPM and have similar...

05 June 2017 2,591 6 View

Understanding JFM Papers

I have noticed this quite often that papers from the esteemed Journal of Fluid Mechanics are very intense mathematically. The topic of the paper looks very attractive but as soon as I get into the...

01 January 1970 8,990 2 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How do you mesh a thin solid in Fluent?

Hello, I have used the shell function on SpaceClaim to create thin solids for the model I am studying. These are contained within an enclosure for my study. I chose this approach as it avoids the...

24 February 2021 8,856 3 View

Ijaz Fazil Syed Ahmed Kabir

outflow boundary condition

Vedant Kumar

Thank You Sir.

Vikash Kumar Singh Chauhan

Actually it depends on the conditions of the region. if the pressure at the boundary is all more than the pressure inside the domain then you can use outflow condition.if there is uncertainty of the pressure change i will suggest you to take long distance downstream of the working area of the domain to reduce the effects and then you can use either pressure outlet or outflow condition.