How to calculate pressure drop across n number of perforated discs?

03 March 2018 0 6K Report

Relations for calculating pressure drop for flow across a single perforated disc are widely available. However if there are n number of discs placed in the direction of flow, how can we calculate the pressure drop across such a setup?

Badges
Science topic

Similar topics
Thermodynamics
Pressure

More Vedant Kumar's questions See All

Gas Turbine Blade Cooling simulation using ANSYS Fluent 18.2. Why does it show divergence in AMG solver?

I am currently working on Gas Turbine Blade Cooling design where inside a turbine blade a cooling channel is incorporated. The cooling channel is made of a single pipe system which is recirculated...

06 July 2019 4,375 2 View

Boundary condition for inlet and outlet for a tesla turbine for simulation in fluent?

I am trying to simulate flow for a tesla turbine. I have axial inlet velocity. What boundary condition should I put at the outlet to check pressure there?

11 December 2017 1,111 4 View

Propeller vs Turbine

Can I model a propeller as a turbine just by changing the value of coefficients like loading coefficient, thrust coefficient,etc to negative given that they rotate at same RPM and have similar...

05 June 2017 2,636 6 View

Pressure at duct inlet

Is there anyway I can decrease the pressure at the inlet of a Converging-Diverging duct while maintaining same far upstream flow conditions? I mean to say that I want to make changes in the duct...

05 June 2017 5,587 4 View

Understanding JFM Papers

I have noticed this quite often that papers from the esteemed Journal of Fluid Mechanics are very intense mathematically. The topic of the paper looks very attractive but as soon as I get into the...

01 January 1970 9,041 2 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Optimal condition for depositing FTO target 95:5% using sputter technique?

Hello I want to know about the sputtering condition of depositing FTO from target 95:5%. I tried with RF sputter in pressure 2.5Pa and 100 sccm Ar at room temperature but it showing no...

21 July 2024 1,680 2 View

What could be the possible reason that sintering of polycrystalline diamond fabricated with tape casting has suddenly started failing?

I make polycrystalline diamond with tape casting followed by HPHT sintering. When i sintered the samples up till May, the sintering was good. When i sintered the samples in June and July at the...

16 July 2024 3,212 5 View

The HCP removal rate is lower than usual in concentration step, why?

Hello everyone. I am working on my LV concentration porject, I use 500Kda hollowfiber to do it. The HCP and BSA removal rate is nearly 80%, but last time, I failed to run it. The HCP hasn't been...

11 July 2024 5,380 0 View

Pressure in Iron Iron Carbide?

What will be the pressure in Iron Iron-Carbide diagram? It is at atmospheric pressure?

05 July 2024 1,891 0 View

How to Perform Randall-Selitto Test (Paw Pressure Test) In Mice?

Hi All, My name is Sumaiya, a PhD student at the University of Queensland. I am looking for some suggestions on how to hold mice and perform Randall-Selitto Test by using Paw Pressure Randall...

30 June 2024 6,004 0 View

How do I dedicate my entire life in doing only one thing?

I would like to dedicate my entire life in doing only one activity alone and nothing else. How do I achieve it in this world full of unavoidable distractions and societal pressures?

24 June 2024 298 1 View

If modulus of elasticity is divided by any inertial or dynamic pressure (1/2rhov^2), is there any dimensionless number present to represent it?

While deriving for a momentum equation with elastic stress effects, I am planning to put a ratio between elastic modulus (in Pa) and dynamic pressure (in Pa) in a simplified form. I am not...

23 June 2024 8,059 1 View

Trying to find a copy of an original paper?

Despite many attempts I am still unable to find the original version of this paper and would appreciate if anyone can locate it for us: Baker PG, Haig G (1981) Metronidazole in the treatment of...

20 June 2024 5,448 3 View