Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

Do anyone here can help us in the field of molecular docking?

We have synthesized various metal complexes with different environment around the metals. Now to see the application of synthesized complexes we need this study also. we are also interested in...

01 March 2021 1,899 2 View

Analysis of CRD two factor using R studio ?

Hello everyone. I have conducted the research on post harvest longevity of tomato crop using plastic packaging and different doses of chemicals as two different factors. The design of experiment I...

28 February 2021 8,189 3 View

What is the exact mechanism of the antimicrobial effect of local anesthetics?

The antimicrobial effect of local anesthetics has been known for more than 50 years, but it still seems to have an unclear mechanism of action. which bacteria? which concentration? etc etc. ....

27 February 2021 4,450 2 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Resistivity of PVD TiNx thin films vs. N2 flow?

In the PVD of TiN thin films (~100A), I've found the resistivity of the TiN films dropped from ~100 to 60um*cm with N2 flow increasing up to the metallic mode ending point; then the resistivity...

21 February 2021 1,864 2 View

What are your alternative data collection methods during the pandemic? What are the pros and cons?

Dear colleagues We are exploring possible data collection methods for environment and behavior research in the context of architectural environments. Have you conducted any Post Occupancy...

16 February 2021 2,575 4 View

Can bio-decomposer be a successful alternative to reduce residue burning?

To maintain the proper crop plan most of the times there is not enough time to make the field ready for the next crop. In this particular context , can bio-decompser be a solution? What about...

16 February 2021 7,068 24 View

Is there any effective FEM solver to perform simulation of balloon inflation with large deformation (e.g. 300% strain)?

Hi! Thank you for your time, attention, and support. I am currently using FEM solver Abaqus to perform a set of balloon inflation simulations, trying to understand the deformation shape, stress,...

14 February 2021 2,524 4 View

Which is the most ecofriendly and effective activated agent for the preparation of activated carbon from sewage sludge?

I am going to prepare activated carbon from the waste activated sludge coming out of WWTP. Can you please help me in understanding, which chemical/physical activating agent will be most...

07 February 2021 9,507 5 View

Why in BET surface area becomes zero but when detag ads des, it shows good value around 150-200? For single crystals is it a good data to publish?

For single crystals can I give BET data in the publication if it is coming around 200. And why it shows zero value surface area but after detag ads or des it shows value, and which one I should...

02 December 2020 7,173 1 View

What is the equation used in the calculation of surface area from BET plot?

I want to know the equation that I should use when I calculated the surface area using a plot like this one in the attachment. What are the parameters required for the calculation?

15 October 2020 8,364 6 View

Is K-silicate gel a porous material?

I coated a stone surface with K-siilcate. Apparently, it does noe seal the surface since the water penetrae the stone easily and the absorption coefficient does not change too much. However, the...

05 October 2020 3,435 5 View

Can we use Aluminum sheet as a substrate for thin film and have surface area calculated from BET?

I am to calculate surface area of a thin-film using BET and use the same thin-film for electrochemical analysis. I have chosen aluminum sheets, will there be any issues with BET??

27 September 2020 8,456 4 View

How can I determine the type of my membrane NF or UF?

20 September 2020 5,531 2 View

How do I interpret for the following N2 adsorption-desorption isotherm?

I have an adsorption-desorption isotherm of N2 from a 900oC-char sample in mixture of CO2+H20 at 90% of conversion. However, I am not sure this curve belong to what type of isotherm according to...

19 September 2020 8,868 4 View

Is it possible to measure surface area of the polymer film using BET analysis?

I need to measure the surface area of the polymer film (PTFE, PET, 50 um thickness) with micro/nano roughness on the surface (not porous). Is it possible through BET analysis? What is the best way...

20 August 2020 8,866 6 View

How to find a surface area for a material with isotherm type 3?

Hello everyone I would like to ask a way to evaluate a precise, reliable and accurate surface area of a material. I used a nitrogen adsorption-desorption analysis on my material, a nanocarbon,...

04 August 2020 7,708 8 View

Why Nd-doped PbTe showed much lower BET surface area than Yb-doped PbTe?

Why Nd-doped PbTe showed a much lower BET surface area than Yb-doped PbTe?

20 June 2020 9,793 3 View