Are there any published values for the thermal conductivity and/or diffusivity of Amazon Fan sediments?

More Jess I T Hillman's questions See All

Define and explain the concept of an organization with particular reference to the school?

in a presentation style

06 February 2024 8,365 9 View

Why do some of my amplicons produce very few or no reads when MiSeq sequencing?

Hello, 2/3 of my amplicons are failing to produce many/any sequences after MiSeq amplicon sequencing and I am lost as to why this might be. Here is a brief overview of the protocols I am...

01 May 2023 5,621 4 View

Is it possible to read GFP emission with a 535nm filter on a microplate reader?

GFPs excitation and emission peaks are 485nm and 509nm respectively but most standard sets of filters seem to include 485nm excitation and not 509nm emission. The closest that pops up seems to be...

01 February 2023 6,278 0 View

What plasticity index to use for quantifying phenotypic plasticity between populations?

I have tree seedlings collected randomly from two populations and grow in a common garden. A subset of each population was then put in an environmental treatment (four treatments and two...

03 October 2022 6,888 1 View

I am writing a paper that uses the Parenting Stress Index (long version) and have mislaid my manual and need the cut off scores? Can anyone help:?

Cut off scores for the PSI

16 January 2022 8,567 1 View

Why is Qubit giving different concentrations for the same sample?

I am using a Qubit to get the concentration of DNA stock (extracted from tissue). It gave me different concentrations for the same sample. 50400 ng/ml a couple days ago vs. 15200 ng/ml today. The...

05 January 2022 6,948 5 View

How to interpret Chao1 values via EstimateR() in R?

Hello, I have abundance data for bird surveys at various sites - for simplicity, let's say I did 10 surveys at each of 10 sites. When I use EstimateR() function in R, it gives me a Chao1 value...

17 November 2021 1,683 3 View

How to set material of silicon carbide with power mos ? And then ,how to choose the physics models with sic power device?

First, I tried change substrate with silicon carbide while I built device on using sentaurus structure editor , but after I simulated sdevice the bandgap of device didn't change ! So,I tried add...

06 September 2021 8,585 11 View

Can you remove a secondary antibody from mounted immunofluorescent-stained tissue?

I used an Alexa 488 anti-rabbit secondary antibody for colon tissue samples (that had gone through FFPE and rehydrated, followed by antigen retrieval) but the stain was really weak and the signal...

13 July 2021 3,735 2 View

How to compare Spearman's correlations between dependent samples?

I'm stuck trying to figure out how to compare Spearman's correlations for dependent samples. I have an n of 57, and I want to compare two dependent Spearman's correlations with one variable in...

12 June 2021 5,215 7 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Matteo Paganoni

http://www.spectrumgeo.com/wp-content/uploads/Berryman_ST_FB_November_2015-MR.pdf Hi Jess! Look at this :) I think may be helpful.. It also shows BSRs

Jess I T Hillman

Great! Thanks Matteo!

David S Goldberg

Hi Jess

take a look Preliminary Report from ODP Leg 155, Sites 930-946. Poss relevant locations and TC data from deep Amazon Fan?

Dave

Hi Dave,

I've been looking through the ODP 155 reports, lots of useful data but not much on thermal properties.

Jess

Rambhatla G. Sastry

I have no idea.