I have spent a lot of time researching the application of Metal Matrix Nanocomposite, but I found nothing useful, this led me to seek outside help and your guidance will be widely appreciated.
Best regards
I am working on microalgae cultivation using waste water. The initial concentration of nutrients were less but the microalgae has achieved biomass growth of 2 g/L. The final concentration of...
08 August 2024 4,812 2 View
FYI Catalyst is MFI zeolite Si/Al = 140,25.40.11.5,15 I am using this catalyst to study methanol to DME conversion
25 July 2024 2,486 2 View
I intend to get an economical and accurate LAB TEST to measure arsenic concentration in blood sample.
23 July 2024 3,654 2 View
In your opinion, I would like to know if a qualitative study with a structured interview can be conducted in writing. In other words, we sent out open questions and asked the interviewees to...
11 July 2024 4,163 4 View
What is Differential-Fed in microstrip patch antenna ? How it is design in CST studio? What is simulation process and procedure to do Differential-Fed in CST studio ?
08 July 2024 7,464 1 View
How to know the TM/TE modes in antenna design in CST studio? Example: TM01 ,TM02 ,TM10, TM12, TM30 like this... how can identify the antenna is operate the above said mode? can any one explain...
08 July 2024 6,609 2 View
what is co-polarization and cross polarization? How can plot it from CST studio? what are steps and process for find out co-polarization and cross polarization from CST studio?
08 July 2024 7,869 1 View
In an antibiotic degradation experiment using metals carbon composites to activate PMS, the results doesn't fit pseudo first or second order kinetics however the degradation efficiency is very...
26 June 2024 6,941 3 View
Hi All . Recently, I conducted Hall measurement experiments at high temperatures on highly p-doped diamond with a doping concentration of 2.5×10^20 cm−3 During these experiments, I observed two...
23 June 2024 4,763 0 View
I'm thinking of how to increase biomass to replace plastic and industrial waste.
23 June 2024 1,871 4 View
Dear All, I need to deposit Glutathione on to ready made PCL nanofiber composite, how can I physically immobilize? which way of incorporation do you recommend, physical deposition or...
18 July 2024 9,725 1 View
I have hemostatic nanofibers of hydrophilic nature. While fibrin formation from fibrinogen can be qualitatively visualized using SEM. What assays can be performed on nanofibers to quantify the...
08 July 2024 3,714 1 View
I tried to prepare aligned PLLA nanofibers by gap electrospinning method. But after the deposition, when I tried to measure its piezoelectric sensitivity, it actually did not exhibit any...
17 June 2024 9,763 0 View
Recently, I am preparing novel electrospun nanofibers for forward osmosis membrane preparation, I am facing following problems: 1. While testing water flux, there is little leakage, although the...
28 May 2024 8,510 2 View
Recently, i use Cd as a doping for ZnO Nanofiber. From some journals, Cd should increase the absorbance of ZnO. But in my case; it was not. Cd-ZnO Nanofiber has lower absorbance than the pure one....
12 May 2024 1,013 4 View
The FTO is deposited on glass substrate
01 May 2024 9,262 1 View
I have used DMSO to treat films with DMSO vapour. Can I use that same DMSO solution multiple times again?
04 April 2024 5,882 2 View
I want to download the free version of image pro plus .
30 March 2024 8,578 0 View
I added 4mass% also get the results of beads clumped together. Is it because the ethanol does not mix well with PET/HFIP?
29 March 2024 2,164 0 View
I have synthesized a nanoparticle which has piezo electric property and dispersed in the polymer solution to prepare nanofibres through the process of electrospinning. Is there any standard method...
18 March 2024 6,780 1 View