Anyone know how to use ANSYS Fluent to simulate a rising bubble in 3D?

More Sara Leonardo's questions See All

Do I need to strip the PVDF membrane before staining it with colloidal gold?

Dear Colleagues, After running Western blot on PVDF membrane and detection using ECL, I would like to stain my PVDF with colloidal gold to be able to allign the ECL image with total proteins on...

02 March 2021 7,829 3 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

Is it okay to mention you distributed your qualitrics study link through social media sites?

Just want to be clear and know it is okay to say I have distributed the qualitrics link through social media such as Facebook, Instagram and Twitter to ensure my target audience is reached in my...

21 February 2021 5,143 2 View

Why samples do not run in resolving gel?

Hello everybody, I have a problem with SDS-PAGE and I do not know why my samples stop at the top of the resolving gel and they do not run through it. The percentage of gel is 15% and the size of...

14 February 2021 9,116 6 View

Do you know of an informal caregiver of a person who has recently received a bone marrow transplant?

We are conducting a pilot study of an intervention for informal caregivers of persons who have recently received a bone marrow transplant in the US. If you know of anyone who might be interested,...

13 February 2021 9,174 1 View

Is it possible that the single-pass absorption exceeds 50%?

Dear researchers It's well-known that the maximum light absorption of any structure can not be greater than 50%. Is it possible that the single-pass absorption exceeds 50%? How?

17 January 2021 2,335 7 View

Most appropriate fit of a standard curve in an enzym-linked lectin assay?

Dear all, I have a question regarding the most appropriate fit of a standard curve in an enzyme-linked lectin assay set-up to quantify the amount of mucin secretion in conjunctival explant...

03 January 2021 1,010 6 View

How do I access Domestic Violence Attitude Scales or find them for free?

Hi, I'm a postgraduate student currently starting up a research project on attitudes towards domestic violence (DV). The study will aim to compare cultural differences between attitudes and...

31 December 2020 781 3 View

A good protocol for protein purification by AKTA?

Hi everybody, Does anyone have a good protocol for protein purification using AKTA? I have tried to purify two proteins but after several attempts it was not successful. So, I really appreciate...

28 December 2020 5,220 15 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Ahmad Sedaghat

You may use ANSYS CFX for multi-phase flows. I doubt if Fluent can handle when you have heavy melt liquid and gas such as argon.

Fangfang Sun

Please describe more clearly.

In fluent, we use different phasesby euler model to define different fluid.

Sara Leonardo

What i want to simulate is a two phase flow where i have a tank filled with water. Inside that tank theres a air bubble in the bottom of the tank. I created a geometry in SolidWorks modelling the tank as a body and the bubble as another body (the body that represents the bubble is inside the body that represents the tank).

I imported the geometry to ANSYS Workbench, but i can´t define the body that represents the bubble as air and the body that represents the tank as water.

Can anyone help me with this? Thanks