How to analyze a particular region of my simulation box in GROMACS?

Hi, I am using GROMACS 5.1.4 to simulate water in contact with a surface. I am only interested to calculate some properties of water near the surface. Let's say at a distance of x nm from the...

03 March 2021 9,989 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

What test should I use to compare two or three means, if data is not normally distributed but sample size is > 30 in each group?

I personally feel this as a most confusing question. As per my understanding, if sample size is > 30, and sample is skewed, we can still use paramteric approach, as it will follow Z...

01 March 2021 1,587 6 View

How to calculate Ligand-active site distance in a ligand-protein complex from MD simulation?

I have run a MD simulation of a ligand-protein complex in GROMACS using CHARMM forcefield. Reviewer has asked me to calculate Ligand-activesite distance and binding free energy of ligand with...

27 February 2021 4,703 1 View

Efficiency of Proximity Feed Patch Antenna ?

Greetings to all of You! I have searched some research papers for the designing of a proximity coupled patch antenna. Researchers are talking about the impedance bandwidth of the antenna but...

24 February 2021 7,662 3 View

Can the Dunn's test be used as an appropriate post-hoc for the G-test?

Research Question: Are red grouse (Lagopus lagopus scotica) a statistically significant proportion of raptor (bird of prey) diets? I am planning on using a series of G-tests (determining whether...

23 February 2021 5,827 3 View

Please help in identification of this insect?

This insect is minute in size around 1 mm and not clearly visible with naked eye.

22 February 2021 5,907 11 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

Where can the fault diagnosis data set of lithium battery be found?

Most of the data sets on the network only contain good information about the voltage and internal resistance of lithium batteries. The data of faulty battery is missing. Who can help me, I will be...

21 February 2021 8,659 1 View

How to define the sink temperature and film coefficient?

Hi, everyone. I am considering the heat conviction during compacting simulation by Abaqus. I was wondering that how to define the sink temperature and film coefficient? Is there any references...

21 February 2021 6,197 1 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

How climate change will influences human and animal behavioral change?

The role of climate change influencing the human behavior as well as economics interest

01 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View