Thermal and mechanical properties of concrete and steel after cooling?

How do the thermal conductivity, specific heat capacity, plastic strain, critical compressive displacement, and thermal expansion of both hot-rolled steel and concrete change after cooling based...

15 February 2021 1,385 5 View

Cross-sectional area and mesh sensitivity in lattice modeling of RC structural elements?

In lattice modeling of RC structures, what is the mathematical concept behind choosing the cross-sectional areas for the simulation of, for instance, beams? Besides, seemingly, simulating the...

26 January 2021 2,638 2 View

What is the best word embeddings method should I use?

Hi dears If I want to do supervised multi-classes classification of specific domain such as history, using one of the deep learning techniques. Which is the best word embeddings method should I...

22 January 2021 1,290 5 View

What is the best lighting design for conservation?

In the museums, the sensitive organic materials need to be displayed under 50 lux or less and aways from any UV or IR. LEDs still have a little amount of UV. What is the better option? Is it...

20 January 2021 5,965 3 View

Fracture energy of concrete at sub-zero temperatures?

Both tensile and compressive strengths of concrete increase with the decrease in temperature. With this in mind and considering that fracture energy is in direct correlation with the so-called...

18 January 2021 8,778 4 View

Is it useful in texts classification to use the keywords expansion method for long-text examples in the training process for deep learning classifier?

Hello, Is it useful in texts classification to use the keywords expansion method for "long-text examples" in the training process for deep learning classifiers? Will it increase the efficiency of...

16 January 2021 9,291 3 View

Why the fracture energy of concrete increases with the rise in temperature?

Given the degradation of mechanical properties in concrete under elevated temperature namely, tensile strength, modulus of elasticity, compressive strength, etc., what is the justification behind...

15 January 2021 3,651 4 View

Is It useful to use text Pre-processing techniques (Stop Words Removal, Stemming) in the sentiment analysis classification?

Hello, I read some papers they used Pre-processing steps with text that will classify based on Sentiment Analysis. My question is, can I use text Pre-processing techniques in the sentiment...

11 January 2021 5,932 7 View

Will increasing the number of synonyms in training set increase classifier efficiency?

Hello, If I increased the number of keywords (Features) of examples in training set pertaining to a particular class regarding to Sentiment Analysis Classification , will increase the efficiency...

11 January 2021 5,299 4 View

What is the best classifier of Deep Learning techniques in Text Classification?

Hello, I've read many review papers about which is the best classifier of Deep Learning in "text classification", some researchers prove that LSTM is the best, Some say CNN is the best, and some...

10 January 2021 909 12 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View

What is the density for pva electrospining?

I'm Juan Carlos, a high school student who is working with electropinning, I made an electropinning machine with a 21g needle and a 30kv high voltage source and the distance between my needle is...

28 February 2021 298 3 View

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Why do a weight decrease for thermal degradation in nitrogen gas condition?

Hi all The question is related to TGA(Thermogravimetric analysis). Thermal degradation easily understood but why do samples weight decrease? altough just binding is broked, the weight of...

26 February 2021 1,100 5 View

Can thermal cycler machines be problematic during PCR?

Hi, my question is about the heating of thermal cycler machines and I hope some of you had experienced a similar thing previously. There are two thermal cycler machines in the lab(BioRad) and for...

26 February 2021 4,777 4 View

No title

I am trying to find how to know the density needed for a pva electrospinning in a 0.6mm neddle, the electrospinning will be from top to bottom and the problem I really have is the solution because...

25 February 2021 2,615 3 View

How to increase solubility of Poly acrylic acid in Dioxane solvent?

I am working with Polyacrylic acid (100.000Da) and instead of water, I need to use another solvent (dioxane) to dissolve PAA. However, because of the high molecular weight, it's quite hard to...

25 February 2021 2,225 5 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View