Any literature available for modeling of rotary desiccant wheel by use of ANSYS?

More D.B. Jani's questions See All

Is any book available to solve PDE ?

Mathematical model of desiccant dehumidifier.

07 August 2019 7,254 8 View

How many solar panels do I need to run HVAC?

Simulation of desiccant based air conditioners.

01 February 2019 2,168 4 View

How to model rotary desiccant dehumidifier by use of computational fluid dynamics CFD?

Simulation of desiccant wheel.

01 February 2019 3,340 4 View

Does a stochastic network will evolve differently each time it is run?

Artificial neural network.

31 December 2018 1,142 8 View

What can be the possible reason for thermal equilibrium in stochastic networks?

ANN.

31 December 2018 6,070 0 View

What is the nature of general feedback given in competitive neural networks?

ANN.

31 December 2018 1,439 0 View

How to apply particle swarm optimization and response surface method in experimental results?

Optimization of desiccant wheel.

31 December 2018 5,169 8 View

How are input layer units connected to second layer in competitive learning networks?

ANN.

31 December 2018 2,732 0 View

Can any one share the fundamental books/papers/technical reports related to PCM Phase change materials?

Simulation of air conditioning

31 December 2018 2,941 1 View

What consist of competitive learning neural networks?

ANN.

31 December 2018 6,060 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Given the current level of natural phenomena cause by the climate change and environmental pollution, will the AI find the technological solutions?

AI-driven technologies offer previously unheard-of capabilities to process enormous volumes of data, extract insightful knowledge and improve predictive models, according to the UN’s World...

31 July 2024 9,733 3 View

Imrose Bin Muhit

I'm not sure how much this article will help you as you didn't provide much information in your question.

Please have a look to this article, ANSYS and TRASYS software were used to predict the results of dehumidifiers and the desiccant cooling systems, respectively.

Article The Experiment and Simulation of Solid Desiccant Dehumidific...

D.B. Jani

Thank you Imrose Bin Muhit sir for your help and support.

Dr. D.B.Jani