How to model rotary desiccant dehumidifier by use of computational fluid dynamics CFD?

More D.B. Jani's questions See All

Is any book available to solve PDE ?

Mathematical model of desiccant dehumidifier.

07 August 2019 7,087 8 View

How many solar panels do I need to run HVAC?

Simulation of desiccant based air conditioners.

01 February 2019 1,989 4 View

Does a stochastic network will evolve differently each time it is run?

Artificial neural network.

31 December 2018 958 8 View

What can be the possible reason for thermal equilibrium in stochastic networks?

ANN.

31 December 2018 5,904 0 View

What is the nature of general feedback given in competitive neural networks?

ANN.

31 December 2018 1,236 0 View

How to apply particle swarm optimization and response surface method in experimental results?

Optimization of desiccant wheel.

31 December 2018 5,001 8 View

How are input layer units connected to second layer in competitive learning networks?

ANN.

31 December 2018 2,515 0 View

Can any one share the fundamental books/papers/technical reports related to PCM Phase change materials?

Simulation of air conditioning

31 December 2018 2,779 1 View

What consist of competitive learning neural networks?

ANN.

31 December 2018 5,872 0 View

What is the advantage of basis function over mutilayer feedforward neural networks?

ANN.

31 December 2018 5,590 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Arena simulation - how do i model the following model in ARENA (see description) (new to ARENA)?

Hello, I'm fairly new to ARENA and I have the following problem: I have two queues in which, in each queue, a different order type arrives (both having an arrival rate of exponential 10). Order...

02 March 2021 2,431 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Md. Washim Akram

https://www.sciencedirect.com/search?qs=model%20rotary%20desiccant%20dehumidifier&show=25&sortBy=relevance

Syed Asad Ali Zaidi

Folowing

D.B. Jani

Thank you Md. Washim Akram sir and Syed Asad Ali Zaidi sir for your support and help.

THank you Washim and Syed Asad for your valuable support.