Ansys fluent : Can you share the steps to solve Multiphase analysis problem in Ansys Workbench.?

More Sampath Suranjan Salins's questions See All

Explain in detail the laboratory and field tests that are conducted on cement. Elucidate the procedures involved?

This question needed to be answered to a civil engineering student studying his first year right now.

22 April 2024 9,118 2 View

Immunoblotting post total protein quantification using SYPRO ruby stain?

Hello all, I am probing for the difference in expression levels of certain proteins involved in fatty acid transport and muscle remodelling in avian skeletal muscle homogenates. I tried using...

03 April 2024 486 0 View

How to improve torque density of motor?

I would like to enhance the torque out of motor by enhancing the dimensions as i have the flexibility to increase the dimensions....In this context I am not changing voltage and current....by...

02 February 2024 319 3 View

Should I add primary data in appendix of my thesis? Is it mandatory?

It is not mandatory, as it is confident data obtained from my subjects. It might lead to judging the students and the institution they belong to. I have the data, but I doubt whether it is...

16 December 2023 6,187 1 View

Preparation of PLA saturated solution?

Is there any solvent with a high flash point (more than 100 degrees C) that can fully dissolve PLA polymer?

01 November 2023 8,816 0 View

How to do standard curve for total terpenoid content using linalool as standard medium?

I used linalool standard for estimating total terpenoid content for my plant sample, different linalool concentration has been taken and finally the supernatant has been discarded, the red...

04 June 2023 8,036 2 View

Any biostatisticians who can perform Probit analysis ?

Im a Phd student , currently doing my research on tooth eruption . The statistical analysis required for my work is Probit analysis . Any biostatistician who can provide statistical assistance ?

17 January 2023 5,621 4 View

How to use biologically synthesized nanoparticles for anti-bacterial assay?

Nps were synthesized using plant

17 October 2022 8,810 3 View

How to measure and control the thickness of biofilm developed on the surface of bio-carrier?

The performance of SBBR for sewage treatment is investigated in a reactor of capacity 10 L. Conventional K1 kaldnes media (30%) was used as a bio-carrier. after acclimatization for 3 weeks,...

24 October 2021 4,363 1 View

Why am I not getting callus initiation in lemon grass and provide me surface sterilization of leaves suggestions?

I've used Ms media for callus induction for lemon grass, but I didn't get besides different concentration of hormones. In addition there is no bulging of my explants and appears the same while...

30 September 2021 5,014 0 View

Are air moisture harvesting technologies effective in combating desertification?

Air moisture harvesting Air water collection devices

06 August 2024 5,473 2 View

Problem with Two-phase simulation?

Hello; I am conducting a CFD study on two-phase flow in a separator, utilizing refrigerant as the working fluid. For this study, I have implemented pressure inlet and pressure outlet boundary...

25 July 2024 2,309 5 View

How indoor air pollution is sampled using TSI quest EVM air monitoring instrument?

please suggest the research paper related to the instrument is used in it.

16 July 2024 8,453 1 View

How to introduce on fluent the optical loss of the wall due to the reflection of the plate towards the environment ?

"When solar irradiation reaches a surface, some of it is absorbed while the rest is reflected. Part of the light absorbed by the surface transforms into heat and increases the module's...

13 July 2024 8,621 5 View

How to add a mass source term in the continuity equation?

Hi, I am trying to model laser cladding in Ansys FLUENT. There are two phase: one is base metal surrounded by an inert gas (shown in the image). I want to add a cladding layer of the same metal....

07 July 2024 1,182 8 View

Why i can't get access to isosurface in fluent?

hello everyone i get into fuent and i select the result icone then i try to create an isosurface but the button is gray so i can't choose it. what's the problem? any suggestion.

03 July 2024 5,418 4 View

How to get the standard free energy of formation (DGFORM) for AIR in Aspen Plus ?

01 July 2024 8,134 3 View

How to solve the question of ansys fluent?

Regarding the system coupling issue where the update of the solution component fails, the system coupling update for fluid flow (Fluent) triggered an exception: "Update Solution Failed."

30 June 2024 7,894 1 View

Human health risk assessment of ambient air pollutants, how to calculate hazard quotient?

I have calculated CDI (inhalation) of Ozone, CO, SO2, NO2, NO, and TSP (total suspended particulate matter) . However I cannot find RfC (Reference concentration) or even NOAEL of any of these...

27 June 2024 4,488 0 View

How to converge PEMFC in Ansys Fluent?

I am simulating 1 cell of PEM with an area of 50 cm². The mesh has an orthogonality of 0.2 for the channels and bipoar plates (polyhedra) and a quality of 1 for the active zones (hexagonal). The...

26 June 2024 2,358 0 View