How to calculate age-standardized prevalence ratio with 95%CI?

I need to calculate the prevalence ratios to show the trend of prevalence of a drug group used by pregnant women over the years (2001-2018). I would like to use the year 2001 with age distribution...

05 January 2021 7,986 5 View

Asalam o alikum, Can anyone please help me in interpretation of XRD data?

Actually, I want to present the in table form (dcal , dexp, 2 thita, hkl) but don't know how to find these values from data.

28 December 2020 6,769 4 View

Is it need to test Cronbach's Alpha for extracted features from data?

As Cronbach's Alpha is usually used for test the reliability of measurements given by questionnaires, however, I wonder that whether I use this test for features extracted from behavioral data. I...

26 December 2020 9,602 2 View

Does CD31 indicate cell viability?

Hi, I am wondering if the immunofluorescent staining of CD31 antibodies can both mark endothelial cells and indicating their viability. In other words, if I perform immunofluorescent staining for...

23 December 2020 5,815 4 View

Doping of r-GO?

if the percentage of doping Au into rGO is too small 1~10%, is it not enough to prevent restacking of r-GO in xrd results, rGO peak appeared at 22.2 and also the peaks of gold nanoparticles so...

21 December 2020 6,091 3 View

XRD peaks for gold nanoparticles ?

is the concentration of gold salt that were added will affect on the peaks appeared. i added a very little amount of gold salt to dope graphene oxide and not all the peaks that proved the...

17 December 2020 9,275 3 View

How to increase titer of Herpesvirus, Adenovirus?

I'm working with Herpesvirus and Adenovirus. For Herpesvirus, I use Vero cell line to activate and check virus titer. For Adenovirus, I use Hela cell line. Recently, I could activate them, but...

16 December 2020 4,073 5 View

If someone has the pdf file of below mentioned reseach paper?

14 December 2020 5,935 3 View

How big can a enhancer deletion be ? how can we obtain homologous deletion clone ?

Hi all, I have tried to use Crispr Cas9 ( plasmid px333_cas9_mCherry) to delete some enhancers. I designed sgRNA using Chopchop website to target both sides of an enhancer to induce homologous...

13 December 2020 942 3 View

How to calculate the fractional vegetation cover (FVC) from Landsat imagery?

Hi folks, I wonder if anyone know how to calculate the fractional vegetation cover (FVC) from Landsat imagery? As far as I have read about that NDVI, NDVIs, and NDVIv are three required input...

07 December 2020 4,054 2 View

How do I determine the degree of polymerization of PEG 400 based on NMR integration?

Hello, I am working on the photocatalytic degradation of PEG 400. I would like to know if it's possible to determine the degree on polymerization based on NMR integration, or by the MW of the...

02 March 2021 6,186 3 View

How to include original NMR data in a manuscript?

hello. i am junior researcher. I received a comment from a reviewer that he could not find NMR data in my submitted paper. I had included the NMR graph with explanation and formula to calculate...

27 February 2021 734 4 View

How to solve the fatal error "the entire source was rejected" in MCNP?

Simple geometry was made having concentric cylinders bounded by a square region. The geometry has a reflective boundary. The source was defined at one point in the boundary and when it had been...

17 February 2021 4,364 3 View

How to combine two geometries in LAMMPS ?

I am trying to simulate contact angle of water on a quartz slab using LAMMPS. I have created and equilibriated the quartz slab and the water cluster separately. Now I want to create a composite...

17 February 2021 5,884 2 View

Is ANSYS Fluent good for simulation of a three phase reactor(stusy of its hydrodynamics or mass transfer...)?

Hello everybody, I would like to simulate a three phase reactor and study its hydrodynamics. I would like to know which type of software is better? I have a good command of ANSYS Fluent and I am...

10 February 2021 4,303 3 View

Does anyone knows about a comercial software to record pressure and temperature during reaction in an Autoclave?

Dear all: Currently I am working with polymerization reaction in a reactor. For this, I need to control temperature, pressure, agitation speed etc. For calculation of rate of polymerization, I...

07 February 2021 355 2 View

How to mesh complex geometry?

I have been trying to mesh some complex geometry and have been having issues. I have attached images of the geometry in question. This structure is very large in size but has some comparatively...

05 February 2021 6,379 5 View

Please recommend me the proper steps (blocking method) to generate Hexahedral mesh of the following geometry inside ICEM-CFD?

I am facing an issue while blocking for the geometry mentioned in the image. After blocking it ends with a triangular block due to its shape. How to create a hexahedral mesh for this geometry in...

02 February 2021 888 1 View

Can anyone recommend me a NMR Handbook?

Hi, I've been searching for a NMR Handbook with 29Si chemical shifts information but I can't find one. Also I've tried to find an online database with that kind of info but I have no lucky. Can...

02 February 2021 307 3 View

Head phantom by MCNP?

Can anyone give an advice about what is the best method to simulate a head phantom by MCNP? I mean, is there any reference to use?

01 February 2021 7,304 2 View