Can I prepare stable CNT - Water nanofluids by only adjusting the pH of the basefluid?

Hi, I wanted to know if it was possible to fabricate a CNT - Water nanofluid that is physically stable by only adjusting the basefluid pH value (i.e. with out adding surfactant or...

31 December 2019 7,083 10 View

How can I calculate the temperature of a PVD beam, if I know the power percentage, voltage, and current ?

Good day everyone, If possible could you provide an equation to calculate the temperature of the e-beam that is used to evaporate the coating source in the PVD system. The equation should contain...

04 May 2018 7,150 5 View

Can I evaporate stainless steel 316L using physical vapor deposition and still get stainless steel coated layer on a surface ?

If I use stainless steel 316L in a PVD as an evaporation source will I obtain a stainless steel 316L coated layer on my substrate ? If yes, can you suggest what power % would be appropriate for...

04 May 2018 2,994 6 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Chlorinated organic formation in odor control scrubbers using hypochlorite?

I'm involved in a study of odor control technologies for municipal wastewater treatment plant. One of the control options involves a chemical 2-stage (acid/alkaline) packed bed scrubber. The...

03 March 2021 3,661 2 View

Which database would give me this list of chemical components?

Dear colleagues: I would like to know if anyone knows of a database that gives me the parameters pH, K, K, Mg, P, C, N, Zn, Cu, Ni and Cd of common foods. I find a lot of information of proteins,...

26 February 2021 5,525 3 View

Why is NH4OH added in heavy metals limit test?

The limit test I'm referring to is USP method II. In this procedure you need to dropwise add 6N of NH4OH to the sample until it the pH is alkali. After that you need to dilute and add HOAc until...

23 February 2021 2,049 3 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

No title

22 February 2021 9,932 11 View

Can anyone help or comment on solubilising chlorobutanol in aqueous injections in minimum time possible?

Please suggest solubilisation of chlorobutanol in injections. Tried pH and high temperature. But the issue is of assay drop. If anyone can suggest any solution. Its a commonly used excipient for...

21 February 2021 7,397 1 View

What reaction will occur when adding hexamine into ammonium nitrate in an acidic medium?

Hello, I am investigating properties of water in oil emulsion explosives. And adding hexamine (hexamethylenetetramine) into one of the phases that are used to make the emulsion should increase the...

21 February 2021 8,680 1 View

What properties of water shall be analyzed and evaluated to test the effectiveness of activated carbon?

I would like to ask what other properties of water (pH and such) shall be analyzed and evaluated to test the effectiveness of activated carbon from filtering the contaminants present in the water?

20 February 2021 9,422 8 View

Phenol-pH graphic?

We want to use phenol pH graphic to measure the pH of mediums before and after inhibitor application to cells. We have phenol absorbence values at 460, 560 and 720 nm wavelength. When we measure...

20 February 2021 7,700 3 View