Abaqus generates two files as .SMABulk and SMAFocus. What does these files tell me?

Tamer Qaimari @Tamer_Qaimari2

03 March 2016 1 11K Report

if anyone knows the meaning of these two files. it would be appreciated.

Jaeho Lee

I normally see those two files when the analysis accidentally stopped.

Badges
Science topic

More Tamer Qaimari's questions See All

Nonlinear large deflection analytical solution of simply supported beam with concentrated load?

Hallo, how to get the nonlinear displacment at the middel of simply supported beam with concentrated force, i want to see the difference between abaqus static without NLGEOM and with NLGEOM. for...

06 July 2016 9,870 2 View

How To calculate Runner Diameter and mass flow rate in injection mold for two cavities?

Hallo, i have two cavities connected in Parallel which i would like to fill with Polymer (Rubber) one cavity get filled earlier than the other, the equation i used is simple mass flow equation...

04 May 2016 5,397 3 View

Can one show me the derivation of circular regression matrix for circular fit?

Hallo, Can someone show me (by derivation) how we get this matrix of circular regression ? Thanks in Advance

04 May 2016 2,859 5 View

Von Mises Stress Equation to calculate Stress Triaxiality in Abaqus?

Hallo, i want to know How abaqus calculates Von Mises stress at integration points. When i use Von Mises Stress equation or Equivalent Stress: Svm= sqrt(1/2) * sqrt[ (S1-S2)^2+(S2-S3)^2+(S3-S1)^2...

04 May 2016 3,184 4 View

How to calculate Runner diameter and other flow calculations for NON NEWTONIAN FLUID analytically?

Hallo guys i have two cavities connected in Parallel which i would like to fill with Polymer (Rubber) one cavity get filled earlier than the other, the equation i used is simple mass flow...

04 May 2016 4,198 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

Why running a restart analysis in Abaqus in Ubuntu OS gives an error as attached when running the same job in Windows doesn't give any error and runs?

I am trying to run a restart analysis, which imports deformed configurations of parts from a generated ODB file. It runs fine in Windows OS but when I try to run it in Linux OS, it is giving some...

29 July 2024 9,572 3 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Abaqus cylinder buckling riks analysis?

hi, I am doing a risk analysis of a cylindrical fuselage with windows. I have applied contact interactions between the different parts, and I have applied a unit value load to a reference point,...

20 July 2024 647 2 View

Abaqus 2023 - How to know how many elements have been deleted during a simulation ?

Hi all, I am using the element deletion process based on a Tsai-Wu criterion through a UMAT with a specific State Value controlling the process (DepVar -> Variable number controlling element...

17 July 2024 1,501 1 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View

Hello, does anyone know how I can get coordinates of two specific points on a moving body in Abaqus when applying a vdload subroutine?

Hello I am trying to simulate repulsive force of two permanent magnets in Abaqus. I have implemented Force equations into a vdload subroutine. sensitive parameters are the center to center...

15 July 2024 3,491 0 View