A quantitative analysis of the size and density of carbides?

11 November 2018 0 10K Report

Dear researchers,

Kindly, I have micro structures of high speed steel grades. How to make a quantitative analysis of the size and density of carbides found in the micro structures.

many thanks

Badges
Science topic

More Athil Al-Ezzi's questions See All

Hi, looking for NHE1 siRNA Sequences?

With results and references if available. thank you.

02 November 2023 7,945 1 View

Which Cell line can be used as control cells?

Which “Cell line can be used as control cells” with the following cell line: C6 cell line. U251 cell line MIA PaCa-2 cell line. PATU8898s cell line. 4T cell line. BT549 cell line.

30 March 2023 1,871 2 View

Differential equations COMSOL?

Greetings, Dear researchers , How to add doping using differential equations physics by COMSOL? Thanks

14 March 2022 5,536 1 View

X ray diffraction ?

Dear colleagues, i have got the attached results in the following picture. may you help me to explain the change, please? X-ray diffraction was used to identify phases, quantify changes in the...

04 May 2018 1,353 6 View

Can I obtain the tensile strength, toughness and yield strength of an alloy?

Greetings, Dear Colleagues, Can I obtain the tensile strength, toughness and yield strength of an alloy if I have the shear, young and bulk modulus or the stress- strain curve of the alloy Many thanks

04 May 2018 1,270 3 View

The effect of volume fraction?

Greetings Dear researchers, May you tell me please, what is the effect of martensite size and volume fraction on the hardness of high speed steel? Many thanks

01 February 2018 2,506 2 View

The magnitude of the load?

Hi everyone I am working on abaqus to get J integral for a compact tension specimen, may you help me, please in term of the magnitude of the load that should be taken according to the attached...

09 October 2017 4,467 7 View

Why I can not obtain a clear solution of ZnSO4 with water?

The solution contains: ZnSO4 + Water+ trisodiumcetrate,? NH4OH was added drop wise to this solution to raise the pH to 6.5. Could anyone help me to find out the problem?

08 September 2017 4,260 5 View

What is the reasonable range of current density for atomic layer deposition? if i want to deposit ion metals on an oxide TiO2 nanotube substrate?

I want to know if there is a specific range for the current of atomic layer deposition. Thanks in advance.

02 March 2017 4,466 0 View

What is the most appropriate solvent can be used to absorb sulfur vapor?

If sulphur element is heated up to 500C in a tube furnace, what is the suitable solvent that can be used to desulphurize the vapor that produced during the heating process? Thanks in advance.

10 November 2016 8,925 3 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Can I base on reverse DNA sequences to perform alignment, convert to amino acids and GenBank submission?

I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?

11 August 2024 5,138 1 View

Baseline drift in HPLC? What causes this?

Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!

11 August 2024 3,770 4 View

Text-Communication from the M1 Hand Area using BCI—and then there is Elon Musk?

Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...

10 August 2024 7,180 0 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

How to prepare the nanoparticle treated fungal sample for Environmental SEM analysis?

A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.

07 August 2024 5,307 1 View