Greetings,
Dear Colleagues,
Can I obtain the tensile strength, toughness and yield strength of an alloy if I have the shear, young and bulk modulus or the stress- strain curve of the alloy
Many thanks
Of course you can obtain your Ys, UTS from the stress-strain curve of the alloy
Strengths are fundamentally different material properties than modulus.
I agree with Seun Owoeye
With results and references if available. thank you.
02 November 2023 7,945 1 View
Which “Cell line can be used as control cells” with the following cell line: C6 cell line. U251 cell line MIA PaCa-2 cell line. PATU8898s cell line. 4T cell line. BT549 cell line.
30 March 2023 1,871 2 View
Greetings, Dear researchers , How to add doping using differential equations physics by COMSOL? Thanks
14 March 2022 5,536 1 View
Dear researchers, Kindly, I have micro structures of high speed steel grades. How to make a quantitative analysis of the size and density of carbides found in the micro structures. many thanks
10 November 2018 9,952 0 View
Dear colleagues, i have got the attached results in the following picture. may you help me to explain the change, please? X-ray diffraction was used to identify phases, quantify changes in the...
04 May 2018 1,353 6 View
Greetings Dear researchers, May you tell me please, what is the effect of martensite size and volume fraction on the hardness of high speed steel? Many thanks
01 February 2018 2,506 2 View
Hi everyone I am working on abaqus to get J integral for a compact tension specimen, may you help me, please in term of the magnitude of the load that should be taken according to the attached...
09 October 2017 4,467 7 View
The solution contains: ZnSO4 + Water+ trisodiumcetrate,? NH4OH was added drop wise to this solution to raise the pH to 6.5. Could anyone help me to find out the problem?
08 September 2017 4,260 5 View
I want to know if there is a specific range for the current of atomic layer deposition. Thanks in advance.
02 March 2017 4,466 0 View
If sulphur element is heated up to 500C in a tube furnace, what is the suitable solvent that can be used to desulphurize the vapor that produced during the heating process? Thanks in advance.
10 November 2016 8,925 3 View
How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...
10 August 2024 942 3 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Details of the Analysis. Static Analysis Composite Layup Continuum Shell Elements FRP Material (Elastic and Hashin Damage)
03 August 2024 8,538 4 View
How do you tie-break and rank these two in their strength?
03 August 2024 4,471 1 View
Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...
03 August 2024 2,546 2 View
What is the role of oxidative stress in toxin-induced carcinogenesis? I am currently researching the impact of environmental toxins on children's health and would greatly appreciate insights from...
02 August 2024 3,174 1 View
How select composition for ods-high entropy alloys?
31 July 2024 2,795 1 View
Any suggestions with respect to etchant composition and holding time?
27 July 2024 6,925 2 View
The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...
27 July 2024 8,508 0 View
i compare between the antioxidant and oxidative stress level between negative control rats (saline) and CCL4 intoxicated rats. i found the level of GSH and TAC is more in toxic group than normal....
26 July 2024 1,887 0 View