Hard, amorphous, brittle, inorganic, usually transparent, polymerous silicate of basic oxides, usually potassium or sodium. It is used in the form... | Contact experts in Glass to get answers
941 views 1,247 posts
Questions related to Glass
Expert suggestions are requested...! In the Plant Tissue Culture, after few days (~10days) of subculture onto a fresh MS medium, plants which are growing in a glass jar, there was leaf...
19 October 2021 8,215 34 View
I am planning to use ATR-FTIR to find polymer type of microplastic sample. it is hard to place sample that is very small (1 mm) in the red spot. Therefore, I am planning to place the sample while...
18 October 2021 7,577 6 View
The available materials are autoclavable glass, kork, plastic
12 October 2021 379 3 View
Dear All I would like to bond my PDMS chip to a glass but the size of my chip will be greater than a usual glass slide. Therefore, I need to bond it to a larger glass. Is that possible? Or can it...
12 October 2021 5,428 3 View
What are the most effective and sustainable measures to prevent leaching from glass (precursor)-based geopolymer? Please recommend your suggestions and publications. Thanks.
11 October 2021 8,624 4 View
In general dentistry metal waste materials are discarded as biomedical waste and handled with other biomedical waste materials,is there any special way of discarding or recycling the metals?
04 October 2021 3,794 4 View
I know that glass is a non-gray emitter and thus emissivity depends on wavelength. But how does the emissivity change at each wavelengths at different temperatures?
02 October 2021 8,245 1 View
I am dissolving PEG 20,000 in DW, after that casting in glass petridish. But the formed films are very brittle and very difficult to peel out from petridish. Please suggest me how to make micron...
29 September 2021 4,562 3 View
45SiO2-24.5Na2O-24.5CaO-6P2O5
26 September 2021 241 1 View
Recently, I was trying to deposit AgCl into the surface of silver wire to make Ag/AgCl electrodes. The silver wire I used is 99% impurities and 0,3 mm in diameter. I used KCl 1 M & 3 M as...
26 September 2021 2,587 8 View
I made channels out of parafilm and also double adhesive tape, and each one has its own set of issues. What is a decent replacement for parafilm in the making of a chamber? Also, I can't use PDMS...
24 September 2021 115 4 View
Fungus gnats are common problem in our glass houses. I am looking for some practical solutions. Chemical methods/ drenching use of non-toxic chemicals are one of the method.
23 September 2021 3,312 1 View
Dear All, I'd like to share my experience with our manuscript (theoretical concept) reviewing process. Currently, we are studying radiation shielding materials, particularly glass substances. The...
22 September 2021 4,879 6 View
We have a waterproof cable that is carrying pulsating currents (in the range of 100-200A, 100ns duration). When we monitor the pulsed current passing through the cable using oscilloscope, when the...
21 September 2021 683 9 View
I have tried with APTES and Glutyraldehyde followed by NaBH4 but didm't get a great result on initial attempt
18 September 2021 4,380 1 View
Using the material Designer in Ansys, I have made a composite from E glass fibre ( chopped )and resin but the resulting youngs modulus (5000 MPa) is far less than the constituent modulus of fibre...
15 September 2021 368 7 View
There have always been a challenge when we want to attach nano-composite on glass surface. Adhesion to glass surface is a very difficult task. Do you have any experience for solving this problem?...
14 September 2021 6,768 3 View
Dear All I would like to use a peristaltic pump that applies minimum shear stress on the roller part. It is also important to have a multi-channel pump since many parallel experiments at the same...
12 September 2021 9,241 3 View
I prepared ZnS by precipitation method and then dip coated them on glass slides as thin films. Should I aneal the films too after dip coating?
02 September 2021 3,860 2 View
i have prepared PMMA polymer using PMMA beads mw 350000 using chloroform as solvent at 40 degree C. and poured in to glass petri- dish. And kept 24 hrs. for drying in room temperature. After...
02 September 2021 8,482 2 View
I am trying to compress some optical quality plastic in compression molding machine in between stainless steel plates at 20,000 psi. However the metal is leaving some impression on the pressed...
01 September 2021 3,405 3 View
I am using the Discrete Ordinate Radiation Model and Solar Loading to incident light rays on the top of the glass plate. My model has a glass plate of 3 mm thickness, and below that, the air is...
30 August 2021 8,019 2 View
I have a narishige PC-10 puller for the job, and haven´t been able to find the right settings in order to obtain a pulled glass pipette with 25-40 um diameter and over a centimeter long in order...
27 August 2021 6,502 2 View
Hello everyone i hope to help, i was sent my article to a journal and I got some revision one of the reviewer comments was : ((According to Table 1, the value of corrosion rate (icorr)...
26 August 2021 3,184 2 View