20 Questions 40 Answers 0 Followers
Questions related from Murtaza Sayed
Please help me in calculating 2FED calculation for C atom. Check the attached figure for details...
12 December 2017 9,467 1 View
How to calculate the ground state and excited states energies?. For details please check the attached picture..
10 October 2017 7,295 7 View
I am using xenon lamp of 300 W (67005, Newport, Oriel Instrument) and light intensity of 45.2 mW cm−2 measured with a broadband radiometer (Newport Corporation) as simulated solar light source....
10 October 2017 3,540 3 View
New Impact factors (JCR2017) for Journals are released now?
06 June 2017 6,556 95 View
Is Elsevier replacing impact factor by CiteScore?
06 June 2017 6,243 9 View
a molecule having absorption maxima at 623 nm shows direct photolysis by UV-254 nm light. what could be the possible reason?
03 March 2017 6,253 3 View
I have synthesized TiO2 thin film with exposed {001} facets on Ti-substarte by hydrothermal technique. I am proposing that because TiO2/Ti films are exposed with {001} facets, so that's why the...
10 October 2016 2,635 3 View
I want to know what is meant by {001} facets of TiO2
04 April 2016 3,988 0 View
I am synthesizing {001} facets TiO2 particles by addition polyvinyl alcohol (PVA) to hydrothermal solution along with HF, and isopropanol : water. I observed that when hydrothermal time is...
04 April 2014 3,023 9 View
I have analyzed a Bezafibrate sample obtained after 90 minutes exposure to UV-radiations on UPLC-MS/MS to identify the formation of byproducts. Now the TIC I obtained has various peaks...
09 September 2013 5,290 1 View
I am synthesizing {001} facets exposed TiO2 film on Ti-substrate. When i add iso-propanol + water along with HF to hydrothermal solution then the % of exposed {001} are higher than when i replace...
08 August 2013 801 0 View
What are the advantages of using TiO2 film on immobilized Ti-support over TiO2 particles for waste water treatment?
08 August 2013 5,630 4 View
To calculate the band gap energy of my synthesized TiO2 film on Ti-substrate i need to calculate the molar absorption coefficient and for that i have to calculate the molar concentration of TiO2....
08 August 2013 2,278 9 View
I am synthesizing TiO2 film. I believe that after calcination of TiO2 at 600 0C. there is a formation of oxygen vacancies related to Ti+3. I am verifying my statement by giving XPS results in...
07 July 2013 1,898 23 View
I am using Digital micrograph for calculation of lattice spacing from HR-TEM image but i don't know how to do it. I think first we have to calibrate the image.
07 July 2013 9,241 6 View
Please suggest me a link from where i can download the software " Digital Micrograph" freely. This software is used to see the lattice spacing of HR-TEM.
07 July 2013 5,360 7 View
I am synthsizing TiO film with {001} facets...After calcination at 600C the peak shift to lower values...
06 June 2013 8,122 1 View
I am synthesizing {001} facets films on Ti-Sheets by hydrothermal route. Can anyone please tell me how to BET of my prepared samples?
06 June 2013 4,414 3 View
I am working with the UV-degradation of bezafiberate in water. Using HPLC- UV detector Bezafiberate has abosrption wavelength of 232 nm and gives peak at 1.7min. I am expecting that during the UV-...
10 October 2012 4,894 4 View
Photocatalytic degradation of PPCPs
09 September 2012 3,493 11 View
