'Modeling Ply ModelingPly.1 is not connected what can cause misaligned solid elements.' !?

01 June 2020 1 6K Report

Hi everyone,

I am trying to model a composite component in ANSYS ACP Pre. After updating ACP I get an error which reads:

'Modeling Ply ModelingPly.1 is not connected what can cause misaligned solid elements.'

Has anyone seen this before? I've searched online and the help tool but can't seem to find an explanation. It seems to be only a warning but I'm worried it might affect my results.

Any help would be much appreciated!

Stalin Kawana

I have the same problem, did you find the answer.

Badges
Science topic

More Sirine Bali's questions See All

How to extract frequencies and mode shapes of a 3D bridge from installed multiple accelero-meter?

Dear all How can I extract the frequencies and mode-shapes of a 3D bridge from the acceleration record of multiple accelero-meters installed on the bridge? Thank you.

04 September 2020 119 6 View

Dataset bitcoin (blockchain) transaction attack ?

I need a dataset for various attack bitcoin (blockchain) transactions. Can you help me please?

16 December 2018 3,717 4 View

How to create a fluid domain for plate het exchanger (PHE) with ansys?

I am currently studying the analysis of flow in a plate heat exchanger. i find problems in creating fluid domain with ansys. there is no couplage between the plate and the fluid domain. Is there a...

03 December 2018 4,956 2 View

How can I apply a Kruskal-Wallis or a Friedman test for 2 or more between- / within-subject factors?

We repeatedly faced a problem when analyzing data in behavioral studies. In more sophisticated experimental designs, we need to handle more factors (e.g., a pharmacological treatment and a...

24 March 2015 3,595 11 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View

Complex wave form in ANSYS?

Is there a way to input wave speed in a complex form on ANSYS? The wave speed I need to assign a material is 325(1+0.11i) however I have been unable to do this thus far. Failing that, is there...

27 February 2021 5,969 1 View