Would really beneficial coating shrimp feed using oil to the cultured species?

21 September 2017 0 2K Report

Badges
Science topic

Similar topics
Correction

More Dr Jannathulla R.'s questions See All

Are you looking for research collaboration ?

we have few papers ready for submission, and we need one co-author for each article who can pay article fee. Interested authors may text here or contact me on my following email id [email protected]

29 July 2024 6,626 0 View

Flow through curved domains?

Hi everyone, I am working on a curved domain in which a ship is situated in the middle (geometry is given below). In my understanding the general fluid flow is parallel to the x axis from inlet to...

25 July 2024 9,058 4 View

What is the Principle of Cysteine-carbazole-sulfuric acid reaction with glucose?

I have been looking for the principle of Cysteine-carbazole-sulfuric acid reaction in research papers and books, but couldn't find it. This reaction is mainly used for the quantification of...

23 July 2024 3,891 0 View

Dear researchers. pl help how to plot jablonski energy level graph and magnetic hysteresis curve in origin?

through origin software

17 July 2024 4,991 0 View

Reversed flow at outlet due to the release of DFBI?

Hi everyone, I am working on a simulation involving restricted canal with ship using DFBI. I am facing reversed flow in my outlet boundaries as the DFBI is released (In 1.25s). Is there any...

17 July 2024 7,032 1 View

Cloning of flaviviruses is difficult i have noticed that cells loose their transformation ability after cloning fragments inside vector any advice?

As flaviviruses genome is very frequently prone to mutation hence it is very difficult to clone whole genome inside vector what kind of vector and cells can sustain such amount of cloning...

11 July 2024 4,284 0 View

I am not getting proper colonies while ligating one of fragments in my vector the colonies seems to be normal but in light it seems lysed any reason?

I am working on cloning of a gene fragment inside my vector everything we tried to do correctly like making insert and vector with utmost care but after ligation the morphology of colonies seems...

11 July 2024 9,010 3 View

Possible reasons for not getting wake effects in free surface?

Hi, I am trying to simulate a ship in a canal. The top width of the canal is 20m, bottom width is 6m, depth is less than 5m. Ship has a length of 11.7m breadth of 4m, draft is 0.62m. The velocity...

10 July 2024 1,732 4 View

The authors are asked to provide and elaborate the explanations and comparison with the existing theoretical and/or experimental works related ?

this is related to Eu doped vanadate based nanophosphor

06 July 2024 2,865 2 View

How is artificial intelligence being utilized to enhance the diagnosis and treatment of sleep apnea?

AI has the potential to improve the management of sleep apnea by personalizing treatment, enhancing diagnostic accuracy, and advancing our understanding of the condition.

03 July 2024 9,393 2 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How can I improve the quality of lamb milk replacer for machine feeding?

Hello everyone, I am researching ways to enhance the quality of lamb milk replacer for machine feeding. I would appreciate any insights or recommendations on the following: Manual vs. Machine...

06 August 2024 6,227 2 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Do you think can be any gas and oil bearing rocks in Eastern part of Iran?

I want to know more about petroleum deposits in Iran.

02 August 2024 8,725 3 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

Heavy Crude oil PVT Data?

Hello i need heavy oil PVT data having viscoisty of 2000-3000 cP. If someone have it or research papers about it, kindly share it with me Thanks

25 July 2024 6,940 1 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

What are the most PROBLEMS of HYBRID nanofluid in oil industry ?

explain your idea

23 July 2024 1,197 0 View