Has anyone worked on a 150 MW Wind Farm in PSCAD software supplying a 120 MW Load?
***Tip: the simulation would be like a type 3(DFIG) Wind Farm with a 120 MW "constant power" load.
I worked on wind farm using PSIM
The Actual Question is that, can Wind farm be able to support a load without a voltage source? can it work independently without the Grid?
The attachment is an example of a typical microgrid with different DGs including DFIG based wind farm. This simulation can be found at PSCAD website too.
Also, the link below could be useful for you:
https://www.pscad.com/knowledge-base/topic-47/v-
Hi I am trying to segment a sentinel2 image. At this stage, I want to run a binary classifier that assigns each pixel to either farm or non-farm pixel. For this purpose, I have 4 10m bands...
15 February 2021 3,596 9 View
I want to extract a protein from polyacrylamide gel to be used for immunization. I am wondering if I need to run PAGE since sds might interfere with the immunization process. Thank you
10 February 2021 8,568 3 View
I want to write a code related to the flutter of aeroelastic wing under unsteady load using doublet lattice method (DLM). I want a good reference with numerical examples or a book which learn me...
25 January 2021 7,488 3 View
Hello. We are planning expression of a restriction enzyme in E. coli, and wondering how much of the corresponding methyltransferase is needed to be expressed in order to protect the host genome...
23 January 2021 2,096 4 View
Please help me find a brief history of Recycled Concrete Aggregate (RCA) CLASSIFICATION in the U.S. any paper or Official U.S. state DOTs' document. Target: To find out how many classifications of...
12 January 2021 7,564 3 View
Hello We performed a study on the intestinal microbiota of rats in six intervention groups (8 rats in each group). It is suggested that since the rats in each group were the same in terms of...
10 January 2021 2,507 4 View
I need to survey the result of the inquiries regarding the origins of the reproduction of income inequality in the india for literature review of my thesis.
23 December 2020 850 3 View
I have four HPLC graphs (for methyl ethyl ketone (MEK) and sulfuric acid and little organic monomers) and I want to analyze them. Is there anyone who can help me with this?
23 December 2020 6,180 3 View
here I'm asking about different variants of 3D software's used to get STL file measurements made from CBCT
20 December 2020 4,450 2 View
I am running a 3D solid model in Abaqus Python script, which is supposed to be analyzed for 200 times as the model has been arranged in a for loop (for i in range(0,199):). Sometimes, I receive...
09 December 2020 7,401 3 View
Hello, I tried to perform a co-simulation between PScad and SIMULINK. I reviewed the requirements of compatibility between them but I still have no clue about this issue. My PScad is 4.6.3 (x64),...
06 January 2021 8,226 1 View
Does anyone have any expertise in PI controller Tuning for HVDC model? PSCAD Model is up and running and requires PI controller tuning to achieve the parameters
12 June 2020 803 3 View
I need a book, chapter or something like that which discusses PV inverters. It explains Mathematical relationships and finally Simulates it.
13 April 2020 7,157 6 View
I have a multiple points from a I-V MOV characteristic from a equipment datasheet, but PSCAD only allows to enter eleven points. I saw there is an option to enter until 100 points from an external...
28 February 2020 2,737 3 View
What are the main parameters that should be entered in pscad for MOV modelling? The MOV will be part of the overvoltage protection circuit of a series capacitor in a transmission line. And how do...
27 February 2020 2,055 2 View
The circuit is shown in the attached picture, It is difficult to find the transfer function right know .In the figure Ictrl is the dc current coming after thyristors switching and Irms is the rms...
05 September 2019 10,008 4 View
02 March 2019 6,836 3 View
Dear Sir, Madame Hello, I am doing my graduation project on 150 KWp PV Grid-Tied network , the grid rating is 400v. I drew the system but I am sure that I have mistakes. I must submit my thesis...
31 December 2018 5,674 0 View
How to fix this error : Make File Error: User library 'Obj_Files_2016_03_25\gf42\MMC_2016_03_25_Exp.obj' does not exist in PSCAD? Does anyone help me? Best Regards.
31 December 2018 7,958 2 View
I'm currently working on a PMU data analysis study, can anyone provide a PMU model to collect some data through PSCAD simulation ?
31 December 2018 5,715 1 View