I use Abaqus to simulate the fatigue crack growth. I use the XFEM Direct Cyclic mode and set the XFEM crack. I set tabular pressure cyclic load, but the result shows that the crack only open can't porpagate. How to solve this problem?
Hi samuel
Please, if you have solved the problem, could you help me
thank you in advance
Hello all,
I am also facing the same issue, crack is not propagating.
Did you get the reason why is it so?
Thank You
Prathmesh Pokharkar Eloualid Chakir has anyone solved the issue . I am facing the same issue.
Due to the unavailability of climate rooms, I want to carry out an experiment that require the use of certain saturated salt solutions especially those that can condition the wood specimen to 35%,...
25 February 2021 8,139 1 View
I'm currently working having problem with the concentration for recombinant protein use in western blot, the one been used is Recombinant Human CD19 Fc Chimera Protein-rndsystem which does not...
24 February 2021 8,514 3 View
I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....
24 February 2021 4,428 3 View
I was wondering if anyone knew how to perform the Haldane correction for SPSS (this is the definition of the correction -...
21 February 2021 2,882 1 View
I am calculating emissions considering the uncertainty of the data to do Monte Carlo simulation. Some variables such as yields have normal, lognormal or even uniform distributions. These must be...
03 February 2021 6,318 5 View
I urgently need a map that shows the point locations of informal settlements in South Africa. I am currently working on a study that seeks to relate protests location to the location of informal...
02 February 2021 4,113 7 View
I am in the process of conducting a meta-analysis assessing effect of adjunct radiotherapy on overall survival. Some of the final studies included for analysis use the same national databases for...
02 February 2021 9,211 2 View
26 January 2021 7,830 4 View
Selfconsistent noncollinear magnetic calculations can be done in VASP. I am wondering how VASP update the spin directions at each local site. For molecular dynamics, VASP search the next...
16 January 2021 1,398 3 View
Hello, Please, I need your opinion. I want to map the depth of 20,000 hectares of land. I have sampling points of 20,000 with their respective depth attributes and photos of the topsoil(less than...
31 December 2020 4,325 3 View
When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...
03 March 2021 4,892 5 View
We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...
03 March 2021 7,975 3 View
We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...
02 March 2021 6,036 1 View
Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...
02 March 2021 4,910 3 View
(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...
02 March 2021 3,309 2 View
I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...
02 March 2021 5,829 1 View
Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...
01 March 2021 8,235 2 View
I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...
01 March 2021 10,078 1 View
Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...
01 March 2021 9,332 6 View
I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...
01 March 2021 6,661 3 View