Why magnetostrictive alloys have higher magnetostriction compared to metal?

21 September 2023 0 6K Report

Magnetostriction of metal alloys like Terfenol-D, Metglas have higher magnetostriction compared to Ni, Co and Fe.

Badges
Science topic

Similar topics
Social Psychology
Attitude

More Sougata Koner's questions See All

What is the cause of the requirement of O2, N2 etc. gases in PLD thin film deposition process?

PLD thin film deposition technique is used to deposits the layers of ceramic oxides by the laser ablation process. There is some use of O2, N2 gas etc. cylinders in this deposition technique. What...

11 December 2023 3,210 2 View

What is the benefits of fabrication of dot like electrodes in the thin film heterostructure?

Many reported thin film heterostructures shows dot like electrode fabricated on the ferroelectric phase to extract voltages or current density from the structure. But, it also can be fabricated a...

20 November 2023 7,126 0 View

Why we are interested in particular level of elements in XPS?

Whenever we irradiated a sample with x-ray(with energy Kev), there is a probability of emission of photoelectron from different core levels. But generally people reports for the XPS peaks for a...

08 September 2023 7,922 4 View

What is reason of higher eddy current loss of magnetostrictive metal alloys?

Eddy current loss in magnetostrictive alloys.

09 July 2023 10,013 0 View

How to determine phase of an unknown compound by XRD technique?

Phase of unknown compound by XRD method

14 June 2023 8,395 26 View

Can I use the square root transform data of a weed population to calculate weed control efficiency?

Weed control efficiency calculation

06 June 2023 5,496 3 View

What are the fabrication methods to fabricate thin film multiferroic heterostructures?

Thin film heterostructures

28 May 2023 9,548 2 View

What are benefits of epitaxially grown thin film rather than polycrystalline thin film? What is the benefits of thin film grown on substrate as phase?

Epitaxial thin film, thin film substrate

21 May 2023 8,975 6 View

How to reduce the clamping effect of thin film substrate?

Clamping effect reduction of thin film

16 May 2023 300 9 View

Why mostly Si or glass substrate is used for thin film deposition technique?

What is the basic reason?

03 May 2023 6,297 6 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,561 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,794 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,924 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,507 0 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,416 1 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

Is there any suggestion on the explanation and reduction of stacking fault defects in high Al content InAlGaAs alloy lattice matched to InP?

24 June 2024 6,644 1 View

Can someone introduce an article about the convergence of the temperature parameter for the SPH part in Abaqus software?

For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...

13 June 2024 2,503 0 View