Due to channel length modulation current in mosfet increases but is this current less than triode region current?

As MOSFET current depends on the channel length and due to channel length modulation drain current increases . What will be the impact on the device?

06 July 2018 6,037 5 View

Is common mode voltage only depends on resistor mismatch in differential amplifier?

1.how common mode voltage measurement is different for dc and ac application? 2.for differential low voltage(microvolt range ) dc measurement using INA ,do i need to concern about common mode...

10 November 2017 7,976 4 View

Why opamp integrator circuit is not affected by miller capacitance?

If we see the input impedance( Zi )seen looking into the inverting input node of the circuit shows its frequency independent(according to Bode Plot)? how is that possible?

05 June 2017 2,965 18 View

What happens to the operating freq of the design if system is operated high voltages?

and also What happens to the operating freq of the design if system is operated at dessert and snow places?how it affects the system operation?

04 May 2017 2,549 3 View

Which topology used in low latency adc architecture?

can anybody clarify what is the difference between latency and settling time for any Analog to Digital converter.

31 December 2016 7,890 1 View

What is the Internal behaivor of BJT in saturation??

I'am trying to understand to internal behaivor of BJT when it's in saturation. why the current Ic is highets in saturation?

07 August 2016 4,727 1 View

How stability is related to bandwidth?

what is the reason if bandwidth increases then stability increases and if bandwidth decreases then stability decreases? how transient response is dependent on the bandwidth?

02 March 2016 1,745 13 View

If the gain of open loop system is doubled the gain margin of the system is

1.not affected 2.doubled 3.halved 4.one fourth of original value

06 July 2015 8,660 0 View

Why Vce(sat)=0.2V?

what will happen if resistor is connected in between emitter and ground

06 July 2015 1,445 5 View

Why fet is better chopper than bjt?

what are the reason?

06 July 2015 1,606 0 View

error in running a model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

error in modelling model in Abaqus

Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1

17 August 2021 0 0 View

MGL tools

20 June 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

what is the simplest definition of ion exchange capacity

What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help

08 May 2021 0 0 View

i have some problem with chtMultiRegionSimpleFoam

--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?

24 March 2021 0 0 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

Irradiation data for JAPAN?

Hi, Could you help me to get the latest (2019, 2020) solar resource data for a particular site in JAPAN? PV GIS and NSRDB data are not in reach to JAPAN, I'm looking for some other database for...

03 March 2021 961 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View